Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for ENGIE EPS easyWallbox
Summary of Contents for ENGIE EPS easyWallbox
- Page 1 INSTALLER MANUAL MODE 2 POWER UPGRADE...
- Page 2 About installation in Mode 2 with Power Upgrade 4.10. Setting the rotary switch 1.2. Assistance 4.11. Case reassembly 1.3. Symbols used 4.12. Configuration via easyWallbox PowerUp ( service app 1.4. Warnings FIRST START SAFETY 5.1. Turning on easyWallbox 2.1. Intended purpose of easyWallbox 5.2.
-
Page 3: Qualified Personnel
Thank you for choosing easyWallbox. Please spend some minutes to Mode 2 and be used up to 32 A, (7.4 kW) in compliance with IEC 61851-1:2017. read the documentation to install and use it safely, discovering all its advantages. -
Page 4: Danger Of Electric Shock And Fire
easyWallbox must be treated and disposed of in compliance with Before putting back or moving easyWallbox, ensure that the device current legislation, separately from normal household waste as is not attached to the power supply. - Page 5 IEC 60947-2, IEC 60947-6-2, IEC 61009-1 or the relevant parts of IEC 60898 series or IEC 60269 series. ENGIE Eps does not assume any liability for damage caused by In the event of a short circuit, the value of I2t at the vehicle connector non-compliant use or unauthorised modifications to the device.
-
Page 6: Essential Safety Instructions
understand all related risks. ENGIE Eps does not assume any liability for avoid use not in accordance with the intended purpose damage to persons or things that may arise from failure to respect the avoid incorrect use of the device ... -
Page 7: Product Description
Size of easyWallbox charging station PRODUCT DESCRIPTION without connector in place 3.1. General description 277 mm 277 mm The case of easyWallbox is in polycarbonate and ensures a high level of stability and lightness. The design of the device is the result of in-depth study intended to provide an ergonomic, lean and intelligent work tool. -
Page 8: Identification Label
Installation of easyWallbox in Plug&Play mode (see User Manual) 3.2. Identification label The identification label is on the backside of the charging station. The information on the label is shown in the Figure below. The data shown may differ from that in the Figure, depending on the version of the product. -
Page 9: Technical Features
IOS version compatibility** 12 or higher Communication Protocol Proprietary questions or doubts concerning easyWallbox’s use, installation, Dynamic Power Management Y, by installing the included sensor and maintenance. Data refer to the first release of the APP and may vary with future evolution... -
Page 10: Installation
- ENGIE Eps does not assume any liability for damage caused by measures and rescue methods in the installation site non-compliant use or unauthorised modifications to the device. easyWallbox... - Page 11 Danger of fire and explosion easyWallbox must be installed in areas where there are no Do not stack loads on the box containing easyWallbox and pay incendiary or explosive substances, such as close to petrol attention to the signs and specific instructions on the package.
-
Page 12: Opening The Package
If several easyWallboxes are installed close together, there must be at When easyWallbox is moved manually, do not trip on the power least 20 cm between each one. supply cable of the vehicle. - Page 13 Wall-mounting height for easyWallbox. Use a drill to make the holes Put the fixing plugs into the in the wall. holes using a hammer. Follow the steps below. Remove the aesthetic cover of easyWallbox set up by mechanical interference in the CASE, using the groove on the bottom.
- Page 14 Remove the power cable from the cable gland (A) Risk of electric shock. Before starting installation, be sure that easyWallbox is not connected to any power supply. Any operation of installation, maintenance and dismantling shall be done only when power supply is switched off on your service panel.
- Page 15 All safety requirements concerning RCD and MCB installation listed in chapter 2.1 should be followed. If not present, proceed with the installation of the socket in proximity of easyWallbox. For the installation, please refer to the plug specific instructions. Once installed, please proceed to next instruction.
-
Page 16: Power Supply Connection
The power supply to Before starting installation, be sure that easyWallbox is not connected thermal-magnetic miniature circuit breaker (MCB) mounted in the to any power supply. Any operation of installation, maintenance and service panel to protect the electrical circuit. - Page 17 4.10. E = 26.5 mm F = 6.1 mm easyWallbox can work even without Dynamic Power Management: To connect the current sensor: in this case the installation of a dedicated sensor is not necessary, but blackouts avoidance is not guaranteed.
-
Page 18: Setting The Rotary Switch
POSITION 1: DPM is always turned off - Before connecting to a power supply, make sure that easyWallbox easyWallbox POSITION 2: DPM can be enabled or disabled via the ... - Page 19 The following table contains indicative values of maximum currents for 4.12. Configuration via easyWallbox PowerUp (service app) each installation country, to be checked however before any installation: Country Current limit with Country Current limit with Power Upgrade [A] Power Upgrade [A] Germany 11.
-
Page 20: First Start
- Simultaneous use of My easyWallbox and smart charging function from the vehicle may lead to minor functional issues. To authenticate the smartphone, frame the QR code as required by the... -
Page 21: Charging Procedure
LED status indicator CHARGING PROCEDURE There is a strip of LEDs on the front of the charging station which Once installation is completed, recharging an electric vehicle with easyWallbox combines visual signals and alarms indicating the status of is very easy. easyWallbox:... -
Page 22: Stop Charging
Directly through electric vehicle dedicated control (see the vehicle instruction manual for more details). Using My easyWallbox app. Once the process is stopped, refer to the next chapter. Please note that, once the charging process is stopped, the connector must be extracted f rom the vehicle before the charging process can be restarted. -
Page 23: Maintenance
If the device is damaged, follow the instructions below precisely to avoid dangerous situations, with the resulting damage to persons or things: The only part that can be removed f rom easyWallbox is the avoid using the damaged device ... -
Page 24: Dismantling And Storage
4). Risk of electric shock. Before starting dismantling, be sure that the easyWallbox is not connected to any power supply. Any operation of installation, maintenance and dismantling should only be done when the power supply is switched off on your service panel and the industrial connector is removed. - Page 25 Remove the power supply cables (if preferred) Unscrew the three screws in the wall. Disconnect the wires connected to the J1 tool-free ‘push-lock’ terminals (4). Disconnect the earthing wire connected to the J3 ‘Faston’ terminal (2). Remove the power cable from the cable gland (A). ...
- Page 26 - the temperature of the place where the device is stored must be If you have any questions about the installation of easyWallbox, contact between -25°C and +40°C the authorised assistance centre. Various assistance centres available to - the average temperature over 24 hrs must not exceed 35°C...
- Page 27 The Italian version of this manual is the original. Instructions in other languages are translations of the original manual. ENGIE Eps will not be held responsible for any damage that may directly or indirectly result to people, things or animals due to the failure to comply with all the prescriptions indicated in this Manual and the warnings regarding the installation, use and maintenance of the easyWallbox.
Need help?
Do you have a question about the easyWallbox and is the answer not in the manual?
Questions and answers