Kisae 120V Series Owner's Manual
Charger
Hide thumbs
Also See for 120V Series:
- Owner's manual (32 pages) ,
- Owner's manual (2 pages) ,
- Owner's manual (2 pages)
Advertisement
Advertisement
Related Manuals for Kisae 120V Series
Summary of Contents for Kisae 120V Series
- Page 1 Inverter-Charger 120V Series 12V-2000W-80A (BIC1220080) 12V-3000W-100A (BIC1230100) 24V-2000W-40A (BIC2420040) 24V-3000W-50A (BIC2430050) 230V Series 12V-2000W-80A (BIC1220080i) 12V-3000W-100A (BIC1230100i) 24V-2000W-40A (BIC2420040i) 24V-3000W-50A (BIC2430050i) Owner’s Manual...
- Page 2 Important Please be sure to read and save the entire manual before using your KISAE Sinewave Inverter-Charger. Misuse may result in damage to the unit and/or cause harm or serious injury. Read manual in its entirety before using the unit and save manual for future reference.
- Page 3 IMPORTANT SAFETY INFORMATION This section contains important safety information for the Sinewave Inverter-Charger. Before using the unit, READ ALL instructions and cautionary markings on or provided with the unit, and all appropriate sections of this guide. The Sinewave Inverter-Charger contains no user-serviceable parts. See Warranty section for how to handle product issues.
-
Page 4: Table Of Contents
Table of Contents INTRODUCTION ..................... 5 PRODUCT DESCRIPTION................5 UNDERSTANDING THE UNIT ................ 6 INSTALLING THE UNIT ................10 UNIT OPERATION..................13 TROUBLESHOOTING .................. 24 SPECIFICATIONS ..................25 WARRANTY ....................27 Page 4... -
Page 5: Introduction
1. INTRODUCTION Thank you for purchasing the KISAE Sinewave Inverter-Charger. With our state of the art, easy to use design, this product will offer you reliable service by providing True Sinewave AC power for your home, cabin, boat, RV or trailer and recharge your battery automatically when utility AC is available. -
Page 6: Understanding The Unit
3. UNDERSTANDING the UNIT WARNING: It is recommended that all wiring be done by a certified technician or electrician to ensure adherence to the applicable electrical safety wiring regulations and installation codes. Failure to follow these instructions can damage the unit and could also result in personal injury or loss of life. CAUTION: Before beginning unit installation, please consider the following: •... - Page 7 Typical Wiring Block Diagram of Inverter-Charger: ○ a Battery Bank • The use of deep cycle battery is highly recommended for power inverter application • For battery size, you need to identify how much and for how long the inverter has to provide AC power to the loads (based on Amps x hour energy consumption).
- Page 8 ○ d DC Input • All DC Input Wires should be insulated multi-strand low resistance wires. • The DC wires must be copper and rated 105℃ minimum. Thinnest DC Input Wires Gauge Used Model ≤ 5 feet (Recommended) ≤ 7.5 feet ≤...
- Page 9 ○ ○ h AC Output Socket and i AC Output Thermal Breaker: A single AC Output socket is provided for direct AC output from the unit. An over-current protective device (thermal breaker) is connected in series with the AC Output Socket to avoid over current being withdraw from the AC Output socket.
-
Page 10: Installing The Unit
4. Installing the Unit WARNING: Explosion hazard! • DO NOT install the unit near flammable fumes or gases (such as propane tanks or large engines). • AVOID covering the ventilation openings. Always operate unit in an open area. Choosing the location: The unit should only be installed in locations that meet the following requirements: •... - Page 11 instructions for more details. AC Input and AC Output Hardwire Connections: Warning: Before making any AC Input and AC Output Hardwire connection, please be sure the AC Input Source is not energized and the DC disconnect switch is switched OFF.Please double check the location of the AC input connector located inside the wiring compartment.
- Page 12 Quick Test on Unit after Installation: • Connect a small AC load like 40W light bulb to the AC Output of the unit. • Switch DC disconnect switch to ON to provide battery power to the unit, then press and hold ‘On/Off button on Main unit or ‘Power’...
-
Page 13: Unit Operation
5. UNIT OPERATION The unit is preset with factory default settings and will fulfill the basic needs for inverter-charger operation. Display is used to provide information about the unit status and the unit function can be customized through the Display. Once the unit function is customized, Display can be removed if desired, as the unit can run without the Display. - Page 14 d) To save the new setting, press and hold button until display stops flashing. Understanding the Unit Functions Function Display Description and Available Setting Inverter : Use as Inverter only. No By-pass functions. : Auto Backup. Inverter automatically turns ON when AC Blackout. (Default) : Manual Backup.
- Page 15 Understanding the Display ICONs during Unit Operation Icon Meaning Solid: Unit is running as Charger and is charging the battery Solid: Unit is running in By-pass mode, AC Output is available from AC Input Source. - AC Output is available at both the AC Output socket and the AC Output Hardwire terminal if AC Output switch is turned On (indicated by AC Output indicator on the Display and the main unit being On).
- Page 16 Understanding of Ignition Start ON/OFF function With the setting that required manual On/Off of the inverter, the ignition start port share the same function as the Power On/Off functions on the unit. Providing a +12V dc to the Ignition Start Port will turns on the inverter and removing the +12VDC to the port will turns Off the inverter.
- Page 17 Exploring the Unit Settings a) Inverter and Charger Functions Automatic Backup with Charger set to On (Default setting) By-Pass Unit is running in By-Pass mode. Both AC Output Hardwire and AC Output Socket are Mode Display connected to AC Input Source. - AC Charger is enabled and will charge the battery, battery icon shows Battery Charging stage.
- Page 18 Manual Backup with Charger set to On By-Pass Unit is running in By-Pass mode. Both AC Output Hardwire and AC Output Socket are Mode Display connected to AC Input Source. - AC Charger is enabled and will charge the battery, battery icon shows Battery Charging stage.
- Page 19 Manual Backup with Charger set to Off By-Pass Unit is running in By-Pass mode. Both AC Output Hardwire and AC Output Socket are Mode Display connected to AC Input Source. - AC Charger is disabled. Unit will not charge the battery. When this setting is used, a separate AC Charger or other battery charging source is required to charge the battery.
- Page 20 No Backup and Charger set to On By-Pass Unit is running in By-Pass mode. Both AC Output Hardwire and AC Output Socket are Mode Display connected to AC Input Source. - AC Charger is enabled and will charge the battery, battery icon shows Battery Charging stage.
- Page 21 AC Bypass only, Charger set to Off. By-Pass Unit is running in By-Pass mode. Both AC Output Hardwire and AC Output Socket are Mode Display connected to AC Input Source. - AC Charger is disabled. When this setting is used, a separate AC Charger or other battery charging source is required to charge the battery.
- Page 22 Bulk / Float Voltage Setting: Battery Type Bulk Voltage - Default Float Voltage - Default 14.2V (13.8-14.8V Selectable) 13.8V (13.0-14.0V selectable) Flooded 14.4V (13.8-14.8V Selectable) 13.5V (13.0-14.0V selectable) 14.3V (13.8-14.8V Selectable) 13.4V (13.0-14.0V selectable) Lithium 13.9V (13.8-14.8V Selectable) 13.5V (13.0-14.0V selectable) Program 13.8V (13.8-14.8V Selectable) 13.2V (13.0-14.0V selectable)
- Page 23 Flooded Battery Equalization Setting: Equalization setting can only be used on Flooded batteries. Before the equalization begins, the unit will automatically fully charge the battery first, followed by one hour of equalization. Check the battery electrolyte level during the equalization period. If necessary, refill with distilled water only. All cells should have similar electrolyte levels.
-
Page 24: Troubleshooting
6. TROUBLESHOOTING To troubleshoot the unit, please note the error code displayed on the main unit and review “Understanding the Error Codes” in section 5. Problem Possible Cause/Condition Solution No AC Output at The thermal breaker on the unit is tripped Reset the thermal breaker Press and hold the ‘ESCAPE’... -
Page 25: Specifications
7. SPECIFICATIONS Note: Specifications are subject to change without notices. 12V Input Model 120VAC 12V Model 230VAC 12V Model Specification BIC1220080 BIC1230100 BIC1220080i BIC1230100i Running as Inverter AC Output Power 2000W 3000W 2000W 3000W AC Output Current 16.6A 8.7A 13.0A AC Surge Power (Peak) 4000W 6000W... - Page 26 24V Input Model 120VAC 24V Model 230VAC 24V Model Specification BIC2420040 BIC2430050 BIC2420040i BIC2430050i Running as Inverter AC Output Power 2000W 3000W 2000W 3000W AC Output Current 16.6A 8.7A 13.0A AC Surge Power (Peak) 4000W 6000W 4000W 6000W AC Output Voltage/Frequency 120 VAC / 60 Hz 230 VAC / 50Hz AC Output Waveform...
-
Page 27: Warranty
The limited warranty program is the only one that applies to this unit, and it sets forth all the responsibilities of KISAE. There is no other warranty, other than that described herein. Any implied warranty of merchantability of fitness for a particular purpose on this unit is limited in duration to the duration of this warranty.
Need help?
Do you have a question about the 120V Series and is the answer not in the manual?
Questions and answers