Kongsberg cNODE Modem Embed Instruction Manual
  1. Manuals
  2. Brands
  3. Kongsberg Manuals
  4. Modem
  5. cNODE Embed
  6. Instruction manual
Kongsberg cNODE Modem Embed Instruction Manual

Kongsberg cNODE Modem Embed Instruction Manual

Hide thumbs Also See for cNODE Modem Embed:
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
cNODE Modem Embed
Instruction Manual
453694/A
September 2019 © Kongsberg Maritime AS

Advertisement

Table of Contents
loading

Related Manuals for Kongsberg cNODE Modem Embed

Summary of Contents for Kongsberg cNODE Modem Embed

  • Page 1 Modem Embed Instruction Manual 453694/A September 2019 © Kongsberg Maritime AS...
  • Page 2 Kongsberg Maritime disclaims any responsibility for damage or injury caused by improper installation, use or maintenance of the equipment. Disclaimer Kongsberg Maritime AS endeavours to ensure that all information in this document is correct and fairly stated, but does not accept liability for any errors or omissions. Support information If you require maintenance or repair, contact Kongsberg Maritime’s...

  • Page 3: Table Of Contents

    Scope of supply........................7 General supply conditions....................7 Receipt, unpacking and storage................7 Support information ......................8 INSTALLING THE CNODE MODEM EMBED CABLES....9 About Electrostatic Discharge (ESD) ................10 Installing the cNODE Modem Embed cables..............11 Installing the transducer cables TD80V................12 Installing the transducer cables TD180................13 Connectors ........................15...
  • Page 4 Modem Embed DRAWING FILE..............33 453694/A...

  • Page 5: About This Manual

    Modem Embed. Target audience This manual is intended for all users of the cNODE Modem Embed. Online information All end-user manuals provided for operation and installation of your cNODE Modem Embed can be downloaded from our website.

  • Page 6: Kongsberg Cnode Modem Embed

    Modem Embed Instruction Manual Kongsberg cNODE Modem Embed Topics System description, page 7 Scope of supply, page 7 General supply conditions, page 7 Support information, page 8 453694/A...

  • Page 7: System Description

    Kongsberg cNODE Modem Embed System description cNODE Modem Embed is designed for the Point 2 Point transfer of data between two cNODE’s or to a surface vessel equipped with any HiPAP or μPAP systems. The cNODE Modem Embed provides flexibility to integrate transponder electronics into a custom pressure housing.

  • Page 8: Support Information

    Support information Should you need technical support for your cNODE Modem Embed you must contact a Kongsberg Maritime office. A list of all our offices is provided on our website. You can also contact our main support office in Norway.

  • Page 9: Installing The Cnode Modem Embed Cables

    Installing the cNODE Modem Embed cables Installing the cNODE Modem Embed cables Topics About Electrostatic Discharge (ESD), page 10 Installing the cNODE Modem Embed cables, page 11 Installing the transducer cables TD80V, page 12 Installing the transducer cables TD180, page 13 Connectors, page 15 453694/A...

  • Page 10: About Electrostatic Discharge (Esd)

    Modem Embed Instruction Manual About Electrostatic Discharge (ESD) Electrostatic discharge (ESD) is the sudden flow of electricity between two electrically charged objects. Such flow can be caused by contact, an electrical short, or dielectric breakdown. Electrostatic discharge (ESD) can cause serious damage to printed circuit boards and electronic modules.

  • Page 11: Installing The Cnode Modem Embed Cables

    Installing the cNODE Modem Embed cables Precautions to prevent Electrostatic Discharge (ESD) Sensitive printed circuit boards and electronic modules must always be transported and stored in protective antistatic packing bags. It as also important that they are not transported or stored close to strong electrostatic, electromagnetic or radioactive fields. If it is necessary to open and touch the printed circuit board or module inside the protective bag, the following precautions must be taken.

  • Page 12: Installing The Transducer Cables Td80V

    Modem Embed Instruction Manual Prepare 8 wires with the appropriate length for the modem interface. Install a crimp terminal in one end of each cable. Install the crimp terminals in a Molex 8–pin receptacle according to the cable drawing.

  • Page 13: Installing The Transducer Cables Td180

    Installing the cNODE Modem Embed cables • 1x Molex 8–pin receptacle 43025-0800 • 8 x Molex Female crimp terminal 43030-0008 Procedure Use a yellow wire (0.5 mm ) and connect the white wire from the transducer with both capacitors and the yellow wire from the transformer.
  • Page 14 Modem Embed Instruction Manual • 1x Molex 8–pin receptacle 43025-0800 • 8 x Molex Female crimp terminal 43030-0008 Procedure Use a yellow wire (0.5 mm ) and connect the white wire from the transducer with the yellow wire from the transformer.

  • Page 15: Connectors

    Installing the cNODE Modem Embed cables Connectors Topics Transducer connector pinout J1, page 15 Modem interface connector pinout J3, page 16 Power connector J4, page 17 Service connector J5, page 18 Transducer connector pinout J1 This is the pin configuration for a female plug, as seen towards the plug (face view).

  • Page 16: Modem Interface Connector Pinout J3

    Modem Embed Instruction Manual Modem interface connector pinout J3 This is the pin configuration for a female plug, as seen towards the plug (face view). Pin number Signal Minimum requirements RS-232 Tx 0.5 mm RS-232 Rx 0.5 mm Ground 0.5 mm...

  • Page 17: Power Connector J4

    Installing the cNODE Modem Embed cables Power connector J4 This is the pin configuration for a female plug, as seen towards the plug (face view). Pin number Colour Signal Minimum requirements External 0.5 mm power (24 VDC) External 0.5 mm...

  • Page 18: Service Connector J5

    Modem Embed Instruction Manual Service connector J5 This is the pin configuration for a female plug, as seen towards the plug (face view). Pin number Signal Minimum requirements Responder trigger + 0.5 mm Not connected Not connected Ground 0.5 mm Not connected Responder trigger –...

  • Page 19: General Acoustic Considerations

    General acoustic considerations General acoustic considerations Take this information into consideration when deploying the transponders. Acoustic range The depth rating should not be confused with acoustic range. The acoustic range is dependent on many factors, and some of the factors are outside control of the user. Vessel system The directivity and coverage area for the vessel system is different, depending on which system you are using.
  • Page 20 Modem Embed Instruction Manual Sound velocity and ray bending Changes in sound velocity through the water column caused by changes in the water temperature and/or salinity can bend the acoustic signal and make it impossible to reach the vessel.

  • Page 21: Operating Procedures

    Operating procedures Operating procedures The transponder is operated from the HiPAP operator station APOS. • Refer to APOS online help for descriptions. 453694/A...

  • Page 22: Spare Parts

    Modem Embed Instruction Manual Spare parts Topics TD80V Spare part, page 23 TD180 Spare part, page 23 Printed Circuit Board (PCB) Spare part, page 23 Capacitor Spare part, page 23 Transformer TD80V Spare part, page 23 Transformer TD180 Spare part, page 24...

  • Page 23: Td80V Spare Part

    • : TD180 Part name • : 417492 Part number Printed Circuit Board (PCB) Spare part • : cNODE Modem Embed Printed Circuit Part name Board (PCB) • : 423908 Part number Capacitor Spare part • : cNODE Modem Embed Capacitor Part name •...

  • Page 24: Transformer Td180 Spare Part

    • Receptacle J1 with 150 mm wires. • Receptacle J3 with 150 mm wires. • Receptacle J4 with 150 mm wires. • Receptacle J5 with 150 mm wires. • : cNODE Modem Embed Cable kit Part name • : 431008 Part number...

  • Page 25: Technical Specifications

    Technical specifications Technical specifications Topics Performance specifications, page 26 Weight and outline dimensions, page 27 Power requirements, page 27 Environmental requirements, page 28 453694/A...

  • Page 26: Performance Specifications

    Modem Embed Instruction Manual Performance specifications These performance specifications summarize the main functional and operational characteristics of the cNODE Modem Embed modem. • : Medium frequency 21 – 31 kHz Operational frequency Electronics • : Max, High, Low and Min (6 dB steps) Transmitting power settings •...

  • Page 27: Weight And Outline Dimensions

    Technical specifications Weight and outline dimensions These weights and outline dimension characteristics summarize the physical properties of the cNODE Modem Embed system. Printed Circuit Board (PCB) • Outline dimensions – : 142 mm Height – : 63 mm Width –...

  • Page 28: Environmental Requirements

    Transmit power • : < 100 mW Standby power Environmental requirements These specifications summarize the temperature requirements and other environmental standards for the cNODE Modem Embed system. • : -5 to 55 °C Operating temperature • : -30 to 70 °C...

  • Page 29: Drawing File

    Drawing file Drawing file Topics Transducer TD80V Low outline dimensions, page 30 Transducer TD180 outline dimensions, page 31 Printed circuit board (PCB) outline dimensions, page 32 453694/A...

  • Page 30: Transducer Td80V Low Outline Dimensions

    Modem Embed Instruction Manual Transducer TD80V Low outline dimensions Drawing 350501 453694/A...

  • Page 31: Transducer Td180 Outline Dimensions

    Drawing file Transducer TD180 outline dimensions Drawing 436632 453694/A...

  • Page 32: Printed Circuit Board (Pcb) Outline Dimensions

    Modem Embed Instruction Manual Printed circuit board (PCB) outline dimensions Drawing 423908 453694/A...
  • Page 33 Drawing file Drawing file The following table lists the Kongsberg Maritime drawings that must be referred to when installing the cNODE Modem Embed. Description Drawing cNODE Modem Embed TD80V Low wiring diagram 430968 cNODE Modem Embed TD180 Mini wiring diagram...
  • Page 35 Instruction Manual, cNODE Modem Embed, Drawing file [453694/A page 35]...
  • Page 36 Modem Embed Instruction Manual This page is intentionally left blank 453694/A...
  • Page 37 Instruction Manual, cNODE Modem Embed, Drawing file [453694/A page 37]...
  • Page 38 Modem Embed Instruction Manual Index 212–076626 capacitor........... 23 description 350501 system ............7 TD80V ............ 23 dimensions 402399 technical specifications........27 transformer........... 23–24 documents 412432 download from website ........5 transformer........... 23–24 download 417492 documents from website ......... 5 TD180 .............
  • Page 39 Index offices scope of supply support ............. 8 basic items ..........7 online size information ..........5 technical specifications........27 order number spare part cable kit ........... 24 cable kit ........... 24 capacitor........... 23 capacitor........... 23 PCB ............23 PCB ............23 TD180 .............
  • Page 40 Modem Embed Instruction Manual unpacking general supply conditions........ 7 vessel system about ............19 website download documents ........5 weight technical specifications........27 what is electrostatic discharge (ESD) ......10 wiring prerequisites ......... 11–13 453694/A...
  • Page 42 ©2019 Kongsberg Maritime...

Table of Contents