Summary of Contents for Vetter SmartFork SmartSupply SF-SUPPLY-V10-00X
- Page 1 Operating instructions ® SmartFork SmartSupply Read the instructions prior to performing any task! Keep for future use! U163-935...
- Page 2 ® SmartFork SmartSupply...
- Page 3 This operating instruction (hereinafter referred to as “manual”) contains fundamental manual safety instructions for handling the VETTER SmartSupply (hereinafter also referred to as "SmartSupply"). Incorrect use of the SmartSupply can lead to serious injuries and mate- rial damage as a result of fires, for example. For this reason, this manual and especially the safety instructions/information contained therein must be read by the competent industrial truck driver prior to assembly, commissioning and maintenance.
-
Page 4: Table Of Contents
Table of contents TABLE OF CONTENTS OVERVIEW Range of application Variants of the SmartSupply Structure, SmartSupply variant BAT Structure, SmartSupply variant CAB EC declaration of conformity SAFETY Symbols in this manual Intended use Safety instructions Safety markings Applicable documents Protection of the environment and disposal 2.6.1 Recycling Personnel requirements... -
Page 5: Overview
Overview Variants of the SmartSupply Overview Range of application Fig. 1: SmartSupply ® The sensor data from the SmartFork applications in the fork blade is transferred to the output device (SmartDisplay) in the cab via a radio connection. In variant BAT, the SmartSupply serves as both the power supply and as a radio connection system through the use of a battery (Fig. -
Page 6: Structure, Smartsupply Variant Bat
Overview Structure, SmartSupply variant BAT Structure, SmartSupply variant BAT Fig. 2: Structure, SmartSupply variant BAT Housing, battery connection Contact holder Opening for pairing procedure CANFLY board V1.0 with SmartSupply shield PCB Housing cover Connection, M8 4-pin connector ® SmartFork SmartSupply... -
Page 7: Structure, Smartsupply Variant Cab
Structure, SmartSupply variant CAB Structure, SmartSupply variant CAB Power supply, VETTER Smart Supply variant CAB The SmartSupply in variant CAB does not have a battery and is supplied with voltage (12 - 24 V DC) via the power source of the industrial truck. -
Page 8: Ec Declaration Of Conformity
EC declaration of conformity EC declaration of conformity AS PER EC MACHINERY DIRECTIVE 2006/42/EC VETTER Industrie GmbH, as the manufacturer, hereby declares that the products listed below comply with the EC Machinery Directive. Name: - SmartSupply power supply/radio connection Model: - SF-SUPPLY-V10-00X, SF-SUPPLY-V20-00X This declaration is void if a change is made to the aforementioned equipment. -
Page 9: Safety
Safety Symbols in this manual Safety Symbols in this manual Safety instruc- Safety instructions in this manual are marked by symbols. The safety instructions are tions introduced by signal words which express the extent of the danger. DANGER! This combination of symbol and signal word indicates an imminently dan- gerous situation which, if not avoided, will result in death or serious injury. -
Page 10: Intended Use
Safety Intended use Example: Loosen the screw. CAUTION! Danger of pinching on the cover! Close the cover carefully. Tighten the screw. Intended use In variant BAT, the SmartSupply serves as both the power supply and as a radio connec- tion system through the use of a battery (Fig. 1). Variant CAB is supplied with voltage via the power source of the industrial truck and serves solely as a radio connection system. -
Page 11: Safety Instructions
Safety Safety instructions Safety instructions Improper repairs WARNING! Risk of injury from incorrectly executed work on the SmartSupply! The faultless function of the SmartSupply ultimately depends on the unchanged state of the SmartSupply. Independent modifications and repairs or the use of third-party components could lead to damage and a loss of functionality as well as serious injuries during use. - Page 12 Safety Safety instructions Risk of fire WARNING! Risk of explosion and fire as a result of damage to the lithium-con- taining battery! The faultless function of the SmartSupply in variant BAT ultimately depends on the intact state of the SmartSupply battery. Independent modifications and repairs as well as damage or opening the battery casing could cause the battery to ignite suddenly and result in serious injuries.
-
Page 13: Safety Markings
Safety Applicable documents Safety markings Type plate Fig. 5: Type plate, SmartSupply The type plate identifies (via the article number it contains) the version of the SmartSupply upon delivery. Do not put the SmartSupply into operation without a type plate. The type plate is positioned on the housing near the battery connection. Broker/client A “B”... -
Page 14: Protection Of The Environment And Disposal
Safety Protection of the environment and disposal > Recycling Protection of the environment and disposal ENVIRONMENT! Danger to the environment from incorrect handling of environmen- tally hazardous substances! If environmentally hazardous substances are handled incorrectly, particu- larly if such substances are disposed of incorrectly, this could cause sig- nificant damage to the environment. -
Page 15: Personnel Requirements
The driver of industrial trucks has proven their ability to drive industrial trucks with a driv- er’s seat or a driver’s platform to the operator and has consequently been assigned con- trol by the operator. The driver of industrial trucks is familiar with the use of the VETTER SmartSupply and the associated dangers. Service specialist... - Page 16 Safety Personal protective equipment Description of The personal protective equipment is explained in the following section: personal pro- tective equip- ment Industrial safety helmet Industrial safety helmets protect the head from falling objects, swinging loads and from bumping against fixed objects. Protective clothing Protective clothing is tight fitting workwear with low tensile strength, short sleeves and without any protruding parts.
-
Page 17: Commissioning
All 18 V variants of the GBA series manufactured by Bosch can be used. Using batteries from other manufacturers is only permitted following con- sultation with VETTER Industrie GmbH Checking the battery’s charge level The batteries recommended for use generally have a button for showing the charge level via an LED display. -
Page 18: Pairing
Commissioning Pairing NOTICE! Inserting the battery carefully In order to prevent injuries and material damage to the battery and SmartSupply, never use force to push the battery into the battery con- nection. Grip the battery securely and push it into the battery connection the correct way up from right to left until the battery clicks into place. - Page 19 Commissioning Pairing Pairing with the SmartDisplay The complete manual and all steps for pairing between the SmartSupply and SmartDisplay can be found in the operating manual for the SmartDisplay in the other applicable documents. Pairing status upon delivery Pairing was already carried out during initial commissioning at the manu- facturer’s premises and must only be repeated when a SmartSupply is replaced.
-
Page 20: Maintenance
Maintenance Daily visual inspection by the driver Maintenance NOTICE! Maintenance intervals Always include an inspection of the SmartSupply as part of maintenance ® procedures for the SmartFork Scale. Daily visual inspection by the driver Personnel: Driver of industrial trucks Protective equipment: Protective clothing Industrial safety helmet Protective gloves... -
Page 21: Replacement Of The Smartsupply
Maintenance Replacement of the SmartSupply Replacement of the SmartSupply Personnel: Service specialist Protective equipment: Industrial safety helmet Protective clothing Protective gloves Safety shoes New pairing necessary after replacement! The SmartSupply needs to be “paired” with the broker following replace- Ä Chapter 3.2 “Pairing ” on page 18. ment of a client The SmartSupply needs to be “paired”... - Page 22 Maintenance Replacement of the SmartSupply Fig. 9: Cable connections of the SmartSupply variant BAT Loosen the connection between the M8 socket housing and the plug of the cable connection to the sensor system by unplugging the plug (Fig. 9). Fig. 10: SmartSupply variant BAT Remove the SmartSupply at the open side of the connection panel (Fig.
- Page 23 Maintenance Replacement of the SmartSupply Replacement, SmartSupply Analogous steps! variant CAB For disassembly and assembly of the SmartSupply variant CAB, the same steps as those for the SmartSupply variant BAT need to be carried out for the most part. The additional cable connection for variant CAB is one difference however.
-
Page 24: Technical Data
Technical data SmartSupply variant BAT Technical data SmartSupply variant BAT Fig. 12: SmartSupply variant BAT Fig. 13: Dimensioning, SmartSupply variant BAT ® SmartFork SmartSupply... -
Page 25: Smartsupply Variant Cab
Technical data SmartSupply variant CAB SmartSupply variant CAB Fig. 14: SmartSupply variant CAB Fig. 15: Dimensioning, SmartSupply variant CAB ® SmartFork SmartSupply... -
Page 26: Index
Index INDEX Applicable documents ..... 13 Safety ........9 Assembly Safety instructions . - Page 28 Deviations and changes are part of our ongoing review and improvement of the product. VETTER Industrie GmbH does not accept any respon- sibility or liability for errors that arise from the use and application of this document. This document, including all parts, is protected by copyright.