Advertisement
Locate the drill in a suitable working area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Avoid unintentional starting.
9
DO NOT force the drill to achieve a task it was not designed to perform.
8
DO NOT allow untrained persons to operate the drill.
8
DO NOT get the drill wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT operate the drill if damaged.
8
DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away
8
from the drill when operating. Flammable waste, such as wiping or cleaning rags, must be placed in a closed metal container and disposed of
correctly.
DO NOT exceed the rated capacity of the drill.
8
DO NOT operate the drill if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT leave the drill operating unattended.
8
DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT pull the cable from the power supply.
8
When not in use switch the drill off, remove plug from the power supply and do not leave until the tool has come to a complete stop.
9
2.
INTRODUCTION
i
Compact bench drill powerful enough to cut through wood, plastic and metal. Easy to operate, smooth and quiet in operation. Suitable for DIY or a
small workshop. 5-Speed settings between 580 and 2650rpm. Safety is ensured by protection guard, no-volt safety switch and access to drive belt
is denied during operation by mechanical protection.
3.
SPECIFICATION
i
MODEL No:
Drilling Capacity (Chuck Size):
Spindle Nose Taper:
Swing:
Spindle centre to column:
Spindle travel:
Number of speeds:
Speed range:
Maximum Distance Spindle to Table:
Maximum Distance Spindle to Base:
Working Table Surface size:
Working Base Surface size:
Base Size:
Column diameter:
Collar diameter:
Overall Height:
Motor Power:
Supply
4. CONTENTS
Unpack the parts listed below and check to ensure they are in good condition. Any queries must be reported to your stockist immediately.
Head Assembly
Column with Flange
3 Bolts and Washers
5. ASSEMBLY
Note: Figures are illustrative and may differ in detail from your drill.
5.1.
Place the column assembly on the base, align holes and secure with the three screws and washers provided.
5.2.
Install the table onto the column and tighten clamp screw (fig.1.A).
5.3.
Carefully place the head assembly over the column and slide it into position. Align head with base.
5.4.
Tighten the two set screws in the right side of the head to lock it into position (fig.2).
5.5.
Screw the three feed handles and knobs into the pinion shaft (fig.3.A).
5.6.
To install chuck open the chuck jaws completely by turning the chuck key counter-clockwise. Place a piece of wood on the drill table (to
prevent the chuck from getting damaged).
5.7.
Fit chuck to protruding end of spindle and hold in place (fig.3.B).
5.8.
Turn feed handles to bring nose of chuck down onto wood (fig.3). Firmly pull on feed handle to seat the spindle taper in the chuck.
5.9.
The safety guard mounting is pre-fitted to the drill head. Remove the three small screws in the guard support channel, insert the guard
and refit the screws, through the holes provided in the guard. Note that the guard is in two parts held together by two screws and wing
nuts.
© Jack Sealey Limited
SDM30
13mm
MT2
208mm
104mm
50mm
5
580-2650rpm
200mm
290mm
158 x 160mm
138 x 180mm
200 x 310mm
46mm
40mm
580mm
185W(350W)
230V
Base
Feed Handles and Knobs (3)
Safety Guard
Original Language Version
Chuck and Key
Table and Bracket
Hex. Keys (2)
SDM30.V2 Issue 5 (2,3) 30/06/20
Advertisement
