Page 2
Les og følg disse instruksjonene før du starter installeringen. Feil installering kan føre til alvorlig skade. Produktet må installeres av en godkjent elektriker. SOMFY er ikke ansvarlig for skader og feil som skyldes at instruksjonene ikke er blitt fulgt. Ta vare på denne Före installation, läs noggrant igenom denna manual och följ se-...
A. ExplAnAtion of uSEr intErfAcE Manual command Manual up, stop and down command up, for zone 1. stop and down for zone 2. Selector for Manual Lock solar and Automatic mode protection up. for zone 1. Cancel and . Navigate up, Select item.
D. MEnu StructurE System Sensors Time / (Demo) / (Test) Settings Wind Precipitation Timer Heat Motor Preserve heat Get heat Threshold Threshold Use Function Use Function Use Function Use Function Test and Demo Set down running time - On threshold - Threshold - Function used? - Function used?
Wiring DiAgrAM Zone 2 Zone 1 Zone 1 Zone 2 Error Side Outside Animeo Solo to… Cable Max distance Remark IB/Zone Switch Min: 3 x 0,6 mm / 19 AWG 1000 m/50 m Max: 3 x 2,5 mm...
Page 6
SElEct nEtWork MoDE Animeo Solo consists of two different modes to control motor relays, IB and RK. Select the type you are using. IB network mode is default. (The switch is located on the printed circuit board.)
J. poWEr up thE controllEr thE firSt tiME Start up Start up Start up Language chosen: Used network mode: Set clock If not correct, change 8:20 English before you continue! Next Next Next Select language. IMPORTANT: If you change the network mode, you must power the controller off and on.
M. chEck SEnSorS Go to . Wind and sun sensors Sensors status / Sensor status should normally show a value higher then zero. If that is the case, then everything is fine. If it’s Sun 1: very dark use a flashlight on the sun sensor to Sun 2: simulate sun and check the value.
Page 9
Nothing seams to work as it used to do Check if there is an error indicated on the LCD or in the error list (see section B+D+N). Contact your supplier or www.somfy.com Tip when testing If you want to test a function, e.g. the sun, you have to wait for the on and off delays.
Przed instalacją należy przeczytać poniższe instrukcje. Nieprawidłowa instalacja może doprowadzić do poważnych obrażeń. Produkt musi zostać zainstalowany przez wykwalifi- kowanego elektryka. Firma SOMFY nie ponosi odpowiedzialności za uszkodzenia i szkody powstałe w wyniku nieprzestrzegania instrukcji. Niniejsze instrukcje należy zachować w razie konieczności ich ponownego zastosowania.
Page 12
D. Struktura menu patrz strona 4 System Czujniki Godzina/ (Demo) / (Test) Czujnik Ustawienia Slonce Opady Timer Cieplo Naped wiatru Trzymanie ciepla Pobieranie ciepla Wartosci progów Wartosci progów Uzyj funkcji Uzyj funkcji Uzyj funkcji Uzyj funkcji Test and Demo Ustaw czas opuszczania - Próg wlaczenia - Wartosc progowa - Funkcja uzyta?
Page 13
I. Wybór trybu pracy w sieci patrz strona 6 Animeo Solo oferuje dwie różne metody sterowania przekaźnikami silników, IB i RK. Wybierz typ, który jest używany. Tryb IB pracy w sieci jest domyślny. (Przełącznik jest umieszczony na drukowanej płytce układu.) Tryb IB pracy w sieci IB to standardowy tryb komunikacji urządzeń...
Page 14
L. Ustawienie czasu opuszczania i obrotu lamel. patrz strona 7 Ustaw czas opuszczania (Set running time) Wprowadź czas (czas opuszczania) potrzebny na przejście osłony słonecznej z pozycji pełnego podniesienia do pozycji, do której osłona ma zostać przesunięta, gdy na przykład funkcje słońca i timera są...
Page 15
Nic nie działa tak jak powinno. Sprawdź, czy na panelu LCD lub na liście błędów zgłoszony jest błąd (patrz sekcja B+D+N). Skontaktuj się z dostawcą lub przejdź na stronę www.somfy.com Wskazówki podczas testowania Aby przetestować funkcję, na przykład słońca, należy poczekać na opóźnienia włączenia i wyłączenia.
Need help?
Do you have a question about the animeo Solo and is the answer not in the manual?
Questions and answers