Subscribe to Our Youtube Channel
Related Manuals for SIGMATEK ETT 1962
Summary of Contents for SIGMATEK ETT 1962
- Page 1 ETT 1962 Touch Operating Panel Date of creation: 04.08.2015 Version date: 18.05.2017 Article number: 01-230-1962-E...
- Page 2 (print, photocopy, microfilm or in any other process) without the express permission. We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsi- ble for technical or printing errors in the handbook and assumes no responsibility for damages that occur through...
- Page 3 ETT 1962 Touch Operating Panel ETT 1962 The ETT 1962 is an intelligent terminal for programming and visualization of automated processes. Process diagnostics as well as operating and monitoring automated procedures are simplified using this terminal. A resistive glass touch screen serves as the input medium for process data and parame- ters.
-
Page 4: Table Of Contents
ETT 1962 TOUCH OPERATING PANEL Contents Technical Data ................ 4 Performance Data ................. 4 Electrical Requirements ............... 5 Terminal ..................5 Environmental Conditions ............5 Display ................... 6 Control Unit ................... 6 Miscellaneous ................6 Mechanical Dimensions ............7 Chemical Resistance .............. 8 Touch Interface ................ - Page 5 TOUCH OPERATING PANEL ETT 1962 Wiring Guidelines ..............17 Ground ..................17 Shielding ..................17 ESD Protection ................17 USB Interface Connections ............17 Process Diagram ..............18 10 Status and Error Messages ..........19 11 Cleaning the Touch Screen ..........27 12 Disposal .................
-
Page 6: Technical Data
ETT 1962 TOUCH OPERATING PANEL Technical Data Performance Data Processor EDGE2 Technology Processor core Internal Cache 32-kbyte L1 Instruction Cache 32-kbyte L1 Data Cache 512-kbyte L2 Cache Internal program and 512-Mbyte data memory (DDR3 RAM) Internal remnant 512-kbyte SRAM (battery buffered) -
Page 7: Electrical Requirements
TOUCH OPERATING PANEL ETT 1962 Electrical Requirements Supply voltage typically +24 V DC minimum +18 V DC maximum +30 V DC Current consumption of power 0.85 A supply at +24 V (without externally connected devices) (with externally connected devices) Inrush current... -
Page 8: Display
ETT 1962 TOUCH OPERATING PANEL Display Type 19" TFT color display Resolution SXGA, 1280 x 1024 pixels Color depth 24-bit (16 777 216 colors) Pixel size 0.294 x 0.294 mm Active surface 376.3 x 301.1 mm Backlighting Contrast typically 2000 : 1 Brightness typically 300 cd/m²... -
Page 9: Mechanical Dimensions
TOUCH OPERATING PANEL ETT 1962 Mechanical Dimensions 18.05.2017 Page 7... -
Page 10: Chemical Resistance
ETT 1962 TOUCH OPERATING PANEL Chemical Resistance Touch Interface Solution Visual Effect Coal tar oil / toluene None Trichloroethylene None Acetone None Alcohol None Benzine None Machine oil None Ammonia None Glass cleaner None Mayonnaise None Ketchup None Wine None... -
Page 11: Connector Layout
TOUCH OPERATING PANEL ETT 1962 Connector Layout Front Connector X6: USB 2.0 Type A Function +5 V 18.05.2017 Page 9... -
Page 12: Status Displays
ETT 1962 TOUCH OPERATING PANEL Status Displays Two status LEDs are located on the front (one red and one green LED). green From activation of the voltage supply until processing of the auto- exec.lsl When the application is running (except when controlled through... -
Page 13: Rear Connectors
TOUCH OPERATING PANEL ETT 1962 Rear Connectors X1: Power supply (4-pin Phoenix Contact) Function n.c. +24 V DC n.c. = do not use X2: Ethernet 10/100 (RJ45) Function BaseT/ Gbit n.c. n.c. n.c. n.c. 18.05.2017 Page 11... - Page 14 By configuring the packet filter (Firewall or Router) accordingly however, it is possible to connect a network with SIGMATEK hardware to a third party network without trig- gering the error mentioned above.
-
Page 15: Applicable Connectors
TOUCH OPERATING PANEL ETT 1962 X5: USB Type A 2.0 Function 4.3.1 Applicable Connectors 4-pin Phoenix Contact plug with spring terminal FK-MCP 1.5/ 4-ST-3.5 (Included with delivery) X2, X3: 8-pin RJ45 (not included in delivery) X5, X6: USB 2.0 (Type A) (not included in delivery) 18.05.2017... -
Page 16: Cooling
A lithium battery is installed at the manufac- turer. After delivery of the ETT 1962 and storage of one year, the lifespan of the battery reaches 3 years. We recommend however, that the battery be replaced every 2 years to ensure optimal performance. -
Page 17: Exchanging The Battery
1. It is not neccessary to save data on the microSD card. These are stored internally in a battery-buffered memory module (SRAM). 2. Disconnect the ETT 1962 supply. After the supply is disconnected, the real-time clock is buffered for at least 5 minutes after the battery has been removed. - Page 18 ETT 1962 TOUCH OPERATING PANEL 5. Insert the new battery with the correct polarity (plus side facing the back of the terminal). 5. Hang up housing again and screw it. 6. Reconnect supply. When exchanging the battery, caution must be taken to avoid a short circuit. Other-...
-
Page 19: Wiring Guidelines
TOUCH OPERATING PANEL ETT 1962 Wiring Guidelines Ground The terminal must be connected to ground through the assembly on the control cabinet or over the connection provided. It is important to create a low-ohm ground connection, only then can error-free operation be guaranteed. The ground connection should have a maxi- mum cross section and the largest (electrical) surface possible. -
Page 20: Process Diagram
ETT 1962 TOUCH OPERATING PANEL Process Diagram Page 18 18.05.2017... -
Page 21: 10 Status And Error Messages
TOUCH OPERATING PANEL ETT 1962 10 Status and Error Messages Status an error messages are displayed in the LASAL CLASS software status test. POINT- ER or CHKSUM messages can also be shown on the terminal screen. Number Message Definition Cause/Solution... - Page 22 ETT 1962 TOUCH OPERATING PANEL WATCHDOG The program was interrupted via the Possible Causes: watchdog logic. User program interrupts blocked over a longer period of time (STI command forgotten) Programming error in a hardware interrupt. INB, OUTB, INW, OUTW instruc- tions used incorrectly.
- Page 23 TOUCH OPERATING PANEL ETT 1962 STOP BRKPT The CPU was stopped by a breakpoint Info in the program. CPU STOP The CPU was stopped by the program- Info ming software. INT ERROR The CPU has triggered a false interrupt Cause:...
- Page 24 OP INSTALLED The operating system has been rein- Info stalled. OS TOO LONG The operating system cannot be loaded; Restart; report error to SIGMATEK. too little memory. NO OPERATING Boot loader message. Restart; report error to SIGMATEK. SYSTEM No operating system found in RAM.
- Page 25 An error has occurred during a floating- ERROR point operation. DIAS-RISC-ERROR Error from the Intelligent DIASMaster. Restart; report error to SIGMATEK. INTERNAL ERROR An internal error has occurred, all appli- Restart; report error to SIGMATEK. cations are stopped. FILE ERROR An error has occurred during a file operation.
- Page 26 ETT 1962 TOUCH OPERATING PANEL C-DIAS ERROR A connection error with a C-DIAS mod- Cause: ule has occurred. The cause of the error is docu- mented in the log file Solution: This depends on the cause S-DIAS ERROR A connection error with a S-DIAS mod- Possible causes: ule has occurred.
- Page 27 TOUCH OPERATING PANEL ETT 1962 C_UNKNOWN_CID An unknown object from a stand-alone or embedded object, or an unknown base class was detected. C_UNKNOWN_CONSTR The operating system class cannot be created; the operating system is proba- bly wrong. C_UNKNOWN_OBJECT Indicates an unknown object in an interpreter program;...
- Page 28 ETT 1962 TOUCH OPERATING PANEL LSL LOAD CONTINUE PRERUN The application is started. PRERESET The application is ended. CONNECTION BREAK Page 26 18.05.2017...
-
Page 29: 11 Cleaning The Touch Screen
TOUCH OPERATING PANEL ETT 1962 11 Cleaning the Touch Screen CAUTION! Before cleaning the touch screen, the terminal must first be turned off to avoid unin- tentionally triggering functions or commands! The terminal's touch screen can only be cleaned with a soft, damp cloth. A screen cleaning solution such as an anti-static foam, water with a mild detergent or alcohol should be used to dampen the cloth. -
Page 30: 12 Disposal
ETT 1962 TOUCH OPERATING PANEL 12 Disposal To dispose of the product, the respective, possibly country-dependent, guidelines must be met and followed. Page 28 18.05.2017... - Page 31 TOUCH OPERATING PANEL ETT 1962 Documentation Changes Change date Affected Chapter Note page(s) 19.04.2016 1.1 Performance Data Table updated Remanent memory 256 => 512 KB 23.09.2016 4.3 Rear Connectors Note microSD 12 Disposal Chapter added 23.11.2016 10 Status and Error Mes-...
- Page 32 ETT 1962 TOUCH OPERATING PANEL Page 30 18.05.2017...
Need help?
Do you have a question about the ETT 1962 and is the answer not in the manual?
Questions and answers