Ultra Start 600 Installation Manual page 9

Advanced vehicle security system
Hide thumbs Also See for 600:
Table of Contents

Advertisement

Installation Guide
PROGRAM MODE - ALARM SETTINGS
Enter Alarm Program Mode - See Page 7. for details on entering Program Mode
Setting 1 - Car Finder/ 5th Channel
1 Car Finder OFF
1 Light Flash
*2 Car Finder ON
2 Light Flashes
Note: To operate the 5th channel on button #4, setting 7 must be programmed for 5th channel output.
Press the Valet Switch 1 time to select setting 1 (This will be confirmed by 1 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Setting 2 - Secure Valet Mode
1 Secure Valet Active
1 Flash
2* Normal Valet Active
2 Flashes
Press the Valet Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Setting 3 - Park Light Output
1 30 Second Parking Lights on Disarm
2 Negative Park Light
3* Normal Parking Lights
Press the Valet Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Setting 4 - Horn Honk Timing
1 5ms
1 Flash
2 20ms
2 Flashes
*3 10ms
3 Flashes
Press the Valet Switch 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Setting 5 - 4th Channel Settings
1 Pulsed
1 Flash
2 Latched
2 Flashes
*3 Active
3 Flashes
Press the lock and Star buttons together to activate the 4th Channel output.
The Shock Sensor and ignition will be bypassed upon 4th channel activation.
Press the Valet Switch 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Setting 6 - Car Jack Mode
1
Door & Button
2
Door, Button 4
*3
Car Jack OFF
Press the Valet Switch 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Setting 7 - Horn/ 5th Channel
1
5th Channel
2
Horn Honk 2
*3
Horn Honk 1
Press the Valet Switch 7 times to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Car Finder Mode Disabled
Car Finder Mode Enabled
Valet only if ignition "ON" and valet switch held for 15 seconds
Valet if ignition "ON" and valet switch held for 5 seconds
1 Flash
Park Lights on for 30 seconds on disarm
2 Flashes
Switches the Park Light and the Trunk Release (3rd Channel) Outputs
3 Flashes
2 Park Light Flashes on disarm
Short (Quiet) Pulses
Long (Loud) Pulses
Normal (Medium) Pulses
Pulsed for 0.75 seconds upon 4th Channel Activation
Latched until repeated or ignition "ON"
Active for as long as the button is held on Transmitter.
1 Flash
Activated upon Button 4 or Door open while Ignition is "ON"
2 Flashes
Activated upon Button 4 or Door open or ignition "ON" and Ignition
3 Flashes
No Car Jack Functions
1 Flash
Pulsed output when activated by button #4
2 Flashes
Horn Honk Output - Full Alarm ONLY
3 Flashes
Horn Honk with Arm & Disarm Chirps
PROGRAMMING
9

Advertisement

Table of Contents
loading

Table of Contents