Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ultra Start 600
Summary of Contents for Ultra Start 600
- Page 1 INSTALLATION GUIDE TECH SUPPORT Western Canada And The United States: 1 (866) 698-5872 Eastern Canada. Bilingual Support: 1 (800) 268-0683 E-Mail Tech Support: support@ultrastarters.com Check Our Web Site: www.ultrastarters.com Advanced Vehicle Security System WWW.ULTRASTARTERS.COM...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Table Of Contents 600 Wiring Diagram Installation Tips Pre-Installation Suggestions Installation Suggestions Mounting The Module Installing The LED Installing The Program Button Connecting The Starter Disable Connecting The Dome Light Supervision Under Hood Connections Mounting The Siren... -
Page 3: Wiring Diagram
Installation Guide Built-in Starter Disable relay. See page. 5 500ma Output Programmable - Menu 2 Connect to (-) door pin (-) Input Connect to hood pin (-) Input Connect to (+) door pin (+) Input Connect to Siren 3amp Output Connect to park lights 15amp Output (+.-) Input... -
Page 4: Installation Tips
INSTALLATION TIPS Recommended Pre-Installation Procedures BEFORE STARTING INSTALLATION: - Discuss the optional features with the customer. - Take a few minutes to review the installation and owners manuals. - Do a walk around the vehicle and check for any damage. - If installing a LED discuss the placement with customer before installing. - Page 5 Installation Guide 14 Pin Connector Pink Channel 4 Output Green (-) Door Input Blue (-) Hood Input Purple (+) Door Input Brown (+) Siren Output White (+) Park lights Blk/White (+/-) Dome Light Blk/White (+/-) Dome Light Orange (-) When Armed Grey (-) Trunk Release Yellow...
-
Page 6: Test The System
QUICK START INSTALL Step 1 - Connect All Of the Following Wires 14 Pin Power Connector Black Ground Input Yellow Ignition Input Main Power Input Brown (+) Siren Output White (+) Park lights Green* (-) Door Input Purple* (+) Door Input *Test for door pin type (Positive or Negative) then connect the appropriate wire (Green or Purple) Step 2- Plug-In The Module When all the connections are done, the control module can be plugged in. - Page 7 Installation Guide Programming Overview Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases. However, this system does incorporate a highly advanced programming system that includes 2 menus with numerous options and settings that can be easily adjusted for custom installations and applications.
-
Page 8: Programming
PROGRAMMING PROGRAM MODE - USER SETTINGS Enter User Program Mode - See Page 7. for details on entering Program Mode Setting 1- Ignition Auto Lock 1 Ignition Lock & Unlock Enabled 2 Ignition Lock Only *3 Ignition Auto Lock Disabled Press the Valet Switch 1 time to select setting 1 (This will be confirmed by 1 LED flashes) Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps. - Page 9 Installation Guide PROGRAM MODE - ALARM SETTINGS Enter Alarm Program Mode - See Page 7. for details on entering Program Mode Setting 1 - Car Finder/ 5th Channel 1 Car Finder OFF 1 Light Flash *2 Car Finder ON 2 Light Flashes Note: To operate the 5th channel on button #4, setting 7 must be programmed for 5th channel output.
-
Page 10: Operations
TRANSMITTER OPERATIONS See Owner’s Guide for More Detail on Operations First Car Operation First Car Second Car Operation & & & 2nd Car then then Transmitter Programming Step 1 - Within three seconds turn the ignition Key ON-OFF-ON-OFF-ON - Leaving Key ON Step 2 - Press and hold the Program Switch - Parking Lights will come ON **if park-lights do not come on at this point, turn key off for 5 seconds, then repeat step 1. -
Page 11: Other Features
Installation Guide System Service Mode ACTIVATING SERVICE MODE 1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode. - Page 12 DIAGNOSTICS Alarm Diagnostics If the alarm system is triggered while armed, the system will retain in memory the cause of the trigger. The diagnostics can then be used to determine what the cause of the trigger was. When disarming the alarm, the siren/horn will chirp 3 times instead of the usual 2 times to indicate the alarm had been triggered.