Spin Master Air Hogs ENTITY Instructions

®

Contents:

1 Entity™ Stunt Plane
1 Controller
1 Charger/Trainer/Display Stand
2 Extra Propellers
1 Tool
Charging
ON/OFF
Indicator
Switch
Light
Toggle
Thrust
Button
CONTROLLER
CONTROLLER
1. Use a Phillips screwdriver to loosen the screw
in the battery compartment door.
2. Remove the battery door.
3. Insert six 1.5 Volt AA batteries (not included).
4. Replace battery compartment door and
refasten the screw.
IMPORTANT:
Be sure to insert the batteries as indicated inside
compartment with the correct polarity.
• Battery installation should be performed by an adult. • Use only batteries recommended. Be careful to install the batteries with the correct polarity, as
indicated. • Do NOT mix old and new batteries. • Do NOT mix alkaline, standard, or rechargeable batteries. • Do NOT attempt to charge non-rechargeable
batteries. • Do NOT short circuit the supply terminals. • Do NOT overcharge the plane's batteries. • Exhausted batteries are to be removed, as they will
adversely affect the performance. • Do not dispose of batteries in fire. Battery may explode or leak. • CAUTION: Plane contains a rechargeable cell. If fluid
leaks from the plane, avoid contact with eyes and dispose of the plane. Only use charger supplied with this package. • Do NOT use any other source to
charge your Entity TM . • Different types of batteries or new and used batteries are not to be mixed. • Do not use rechargeable batteries. • Only batteries of the
same or equivalent type as recommended are to be used. • Rechargeable batteries are to be removed from the toy before being charged
(if removable). • Rechargeable batteries are only to be charged under adult supervision (if removable).
IMPORTANT: BEFORE YOUR FIRST FLIGHT, YOU MUST CHARGE AND DISCHARGE YOUR AIRPLANE FULLY 1 TIME. YOU MUST ALSO REPEAT
THIS STEP WHEN A PROLONGED PERIOD OF TIME HAS PASSED WITHOUT FLYING. FAILURE TO DO THIS WILL RESULT IN SHORTENED
LIFESPAN FOR YOUR AIRPLANE. FOR ALL OTHER FLIGHTS, CHARGE THE BATTERIES ONCE ONLY. DO NOT OVERCHARGE THE BATTERIES AS
THIS WILL PERMANENTLY DAMAGE THE BATTERIES.
STEP 1
Ensure that the ON/OFF
SWITCH on the plane and the
charger are "OFF".
STEP 2
Insert the
CHARGE NOZZLE
into the plane's
CHARGING PORT.
STEP 4
Turn the ON/OFF SWITCH
on charger to "OFF".
Rudder
Antenna
Horizontal
Tail Wing
Plane Body
Main Wing
Propeller
Land
Button
Propeller Tip

BATTERY INSTALLATION

IMPORTANT BATTERY INFORMATION

CHARGING YOUR ENTITY
Charge Nozzle
Charging
Port
TM
INSTRUCTIONS
NO ASSEMBLY REQUIRED
Vertical
Tail Wing
Stunt Flap
Stunt Flap
Adjustment
Knob
Charging
ON/OFF
Switch
ENTITY™ STUNT PLANE
CHARGER/TRAINER/DISPLAY STAND
1. Use a Phillips screwdriver to loosen the screw in the
battery compartment door.
2. Remove the battery door.
3. Insert eight 1.5 Volt D alkaline batteries (not included).
4. Replace battery compartment door and refasten
the screw.
IMPORTANT:
Be sure to insert the batteries as indicated inside
compartment with the correct polarity.
TM
PLANE
ON/OFF
Switch
STEP 3
Start charging by switching the charger's ON/OFF
SWITCH to "ON". Let the plane charge for 5 minutes.
NOTE: The CHARGING LIGHT on the charger will
blink red during charging. When charging is
complete, the READY LIGHT will turn to a solid green.
If the ready light and charging light blink at the
same time, the charger's batteries must be replaced.
STEP 5
Unplug the CHARGE NOZZLE from the
plane's CHARGING PORT.
NOTE: You are now ready to set up your
Entity™ for indoor training.
Ready
Light
Tool
Charging
Light
Propeller
Training
Propeller Tip
Stand
Charger
Port
Base
CHARGER/TRAINER/DISPLAY
Charging Light
ON/OFF
Switch
Charging
Hose
Charge
Nozzle
STAND
CHARGER
ON/OFF
Switch
Ready Light