Table of Contents
Advertisement
5. Technical data
Motor
Power rating P
Idle speed n
0
Carbide saw blade
Number of teeth
Bench size
Table width extension, left/right
Table length extension, rear
Cutting height max.
Height adjustment
Tilting saw blade
Dust extraction connector
Net Weight
Operating mode S6: Continuous operation
with idling (cycle time 10 minutes.)
To prevent unnecessary heating of the motor,
the bench circular saw may only be used in the
following ways:
After operation for 4 minutes (S 6 = 40%) with
normal permitted workload, a break of 6 minutes
must follow, in order to let the circular saw idle
and cool.
Noise emission values
sound pressure level L
sound power level L
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although
there is a correlation between emission and
immission levels it is impossible to draw any
certain conclusions as to the need for additional
precautions. Factors with a potential influence
on the actual immission level at the workplace
include the duration of impact, the type of room,
and other sources of noise etc., e.g. the number
of machines and other neighbouring operations.
With this information the user should at least be
able to make a better assessment of the dangers
and risks involved.
After Sales Support
240 V ~ 50Hz
S6 40% 1700 W
6,500 min
Ø 250 x Ø 30 x 2.4 mm
24T (Coarse Cut - Fitted)
48T (Fine Cut - Spare)
610 x 445 mm
608 x 250 mm
435 x 320 mm
72 mm / 90°
54 mm / 45°
infinite 0 - 72 mm
infinite 0° - 45°
Idle speed
pA
TEL: 1300 922 271
6. Before starting the machine
•
Before you connect the appliance to the
mains supply make sure that the data on the
rating plate are identical to the mains data.
•
Always pull the power plug before making
-1
adjustments to the equipment
•
Unpack the saw and check it for damage
which may have occurred in transit.
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be
properly fitted before the machine is switched
on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been
processed before, watch out for foreign
bodies such as nails or screws, etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
Ø 36 mm
that the machine's moving parts run smoothly.
28.2 kg
7. Installation
Caution: Pull out the power plug before
carrying out any maintenance, alteration or
assembly work on the table circular saw.
7.1 Fitting the base frame (Fig. 4-9)
•
Turn the bench circular saw around and lay it
on the floor
•
Screw the four legs (18) loosely to the saw
with the short hex screws (c) and washers (a).
•
The legs (18) with the two holes which lie one
101 dB(A)
above the other on the underside must be
mounted at the rear of the machine, so that
110 dB(A)
the holes are facing the rear. (Fig. 5)
•
Now fasten the longitudinal and cross struts
(19), as well as the middle struts (20) loosely
with the hex screw (c), washers (a) and nuts
(b), to the legs (Figs. 6, 7).
•
Only screw the hex screws (c) and nuts (b)
loosely. Important: The longer struts must be
used on the sides.
•
Screw the stability bar (22) to the holes on
the rear legs (18) with 2 long hex screws
(c), washers (a), locking ring and nuts each.
(Figure 8)
•
Caution: Both stability bars must be attached
to the rear side of the machine.
•
Now attach the rubber feet (21) to the legs
(18). (Figure 9)
•
Then screw all of the screws and nuts to the
base frame.
EMAIL: service.australia@einhell.com
18
m
Hide quick links:
Advertisement
Table of Contents
