Items Supplied; Proper Use; Technical Data; Before Putting The Machine Into Operation - Taurus bt-mc 355 Instruction Manual

7

4. ITEMS SUPPLIED

• Metal cut-off saw
• 2x Cut-off wheel
• Open-ended wrench
• Instruction Manual
• Quick Start Guide
• Warranty Card and Details
• Warranty Sticker

5. PROPER USE

The metal cut-off machine is designed for cutting metal
commensurate with the machine's size.
The machine is to be used only for its prescribed purpose.
Any other use is deemed to be a case of misuse.
The user/operator and not the manufacturer will be held liable
for damage and/or injuries of any kind that result from such
misuse.
The machine is to be operated only with suitable cut-off
wheels. It is prohibited to use any kind of saw blade made of
HSS, HM, CV, etc.
To use the machine properly you must also observe the safety
regulations, the assembly instructions and the operating
instructions to be found in this manual.
All persons who use and service the machine have to be
acquainted with this manual and must be informed about the
machine's potential hazards.
It is also imperative to observe the accident prevention
regulations in force in your area.
The same applies for the general rules of occupational health
and safety.
The manufacturer shall not be liable for any changes made to
the machine nor for any damage resulting from such changes.
Even when the machine is used as prescribed it is still
impossible to eliminate certain residual risk factors. The
following hazards may arise in connection with the machine's
construction and design:
• Contact with the cut-off wheel in the uncovered cutting
zone.
• Reaching into the cut-off wheel while it is running (injuries
through cutting).
• Kick-back of workpieces and parts of workpieces.
• Broken cut-off wheels.
• Catapulting of damaged or cut-off wheels.
• Damage to hearing if ear-muffs are not used as necessary.
After Sales Support TEL: 1300 922 271

6. TECHNICAL DATA

AC motor
Power P
Idle speed
Cut-off wheel
Footprint
Swiveling range
Vice clamping range
Saw width at 90°
Saw width at 45°
Weight
Sound and vibration
Sound and vibration values were measured in accordance with
EN 61029.
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Important!
The vibration value changes according to the area of
application of the electric tool and may exceed the specified
value in exceptional circumstances.
Keep the noise emissions and vibrations to a minimum.
Only use appliances which are in perfect working order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
7. BEFORE PUTTING THE
MACHINE INTO OPERATION
• Unpack the metal cut-off machine and check it for damage
which may have occurred in transit.
• The machine has to be set up where it can stand firmly, e.g.
on a work bench, or it must be bolted to a strong base.
• All covers and safety devices have to be properly fitted
before the machine is switched on.
• It must be possible for the cut-off wheel to run freely.
• Before you actuate the ON/OFF switch, make sure that
the cut-off wheel is correctly fitted and that the machine's
moving parts run smoothly.
• Before you connect the machine to the power supply,
make sure the data on the rating plate is the same as that
for your mains.
EMAIL: service.australia@einhell.com
240 V ~ 50 Hz
2100 W
n 3800 min
-1
0
Ø 355 x Ø 25.4 x 3.2 mm
480 x 277 mm
0 - 45°
max. 195 mm
Ø 70 / 105 x 45 mm
85 x 45 mm
17.5 kg
101 dB(A)
3 dB
114 dB(A)
3 dB