ORiNG IMG-4312-MN Series Quick Installation Manual

M2M
Gateway
Q I
I N D U S T R I A L
uick nstallation
Introduction
IMG-4312-MN LPWAN (Low-Power Wide-Area Network) series Gateway
with one RS-232/422/485 serial port and two 10/100Base-T(X) ports. The
device provides an IEEE802.11b/g/n Wi-Fi interface featuring a link speed
up to 150Mbps. It can be configured to connect to the Internet by dialing up
the embedded LTE CAT-M1/ CA
T NB1 -
device can transfer data to five host PCs simultaneously for backup
purposes. The IMG-4312+-MN provides P.D. function on its ETH1 port
which is fully compliant with IEEE802.3af PoE P.D. specification. Therefore,
it can receive power via an Ethernet cable to save installation costs and
simplify deployment. IMG-4312(+)-MN Series
Cloud, Internet of Things and Industry 4.0 applications. It is a perfect choice
for remote secured data collection from the factory floor (PLCs, machines,
networking devices) and environmental sensors (temperature, humidity,
noise, pollution, vibration etc.) as well as for serving control commands
coming from Cloud Platforms for changing end-devices status.
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Contents Pictures
IMG-4312(+)-MN
LTE Antenna
Wi-Fi Antenna
QIG
DIN-rail kit
Wall-Mount Kit
4-pin terminal block
3-pin terminal block
Dust cover
Q I G
IMG-4312(+)-MN Series
IMG-4312(+)-MN Series
G
uide
Preparation
Before installation, make sure you have all of the package contents available and a PC
with Microsoft Internet Explorer 6.0 or later, for using web-based system management
tools.
Safety & Warnings
cellular modem. In addition, the
Elevated Operating Ambient: If installed in a closed environment, make sure the operating
ambient temperature is compatible with the maximum ambient temperature (Tma)
specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation of the
equipment is not compromised during installation.
is an innovative product for
Mechanical Loading: Make sure the mounting of the equipment is not in a hazardous
condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the equipment to
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
Dimension
Number
X 1
X 2
PWR1 PWR2 PoE
LTE
Main ANT.
ETH1 ETH2 WIFI
WAN
IMG-4312+-MN
WIFI ANT.
Reset
ETH2
X 1 Serial
ETH1
P.O.E. Rx Tx
10/100M
LTE
AUX ANT.
45.0
X 1
X 1
Panel Layouts
X 2
4 13
1
PWR1 PWR2 PoE
X 1 2 5 LTE
ETH1 ETH2 WIFI Main ANT.
3
WAN
IMG-4312+-MN
9
WIFI ANT.
7
Reset
X 1
8
ETH2
Serial
ETH1
P.O.E. Rx Tx
X 2
10/100M
LTE
AUX ANT.
1907-200-M4312MNXX1-FX015
Unit =mm (Tolerance ±0.5mm)
22.52 30.38 23.0
26.9
13.1
81.0
45
22.3
PWR1 PWR2
LTE
Main ANT.
ETH1 ETH2 WIFI
WAN
14.0
IMG-4312-MN 15.5
WIFI ANT.
Reset
ETH2
Serial
ETH1 Rx Tx
10/100M
LTE
AUX ANT.
Front Panel
4
1. LED for Power 1 module
6 6
2. LED for Ethernet ports
1
PWR1 PWR2
2 5 LTE
ETH1 ETH2 WIFI Main ANT. 3. LED for WAN status
3
WAN
4. LED for Power 2 module
IMG-4312-MN
9
5. LED for Wi-Fi status
WIFI ANT.
7 6. LTE antenna connector
Reset
10 10 7. Reset button
8
ETH2 8. Ethernet ports (ETH1 as LAN port; ETH2 as
Serial
WAN port)
11 11
ETH1 Rx Tx 9. Wi-Fi antenna connector
12 12
6 6
9 10. Serial port
10/100M
LTE
AUX ANT.
11. TX status of serial port
12. RX status of serial port
13. PoE indicator (IMG-4312+ Series only)
PRINTED ON RECYCLED PAPER
Industrial Cellular M2M Gateway
Rear Panel
1. Din-rail screw holes
1
Installation
DIN-rail
Step 1 : Slant the device and screw the Din-rail kit onto the back of the device, right in the
middle of the back panel.
Step 2 :Slide the device onto a DIN-rail from the Din-rail kit and make sure the device clicks into
the rail firmly.
40.0
Wall-mount
Step 1: Screw the two pieces of wall-mount kits to the top and bottom panels of the device. A
total of eight screws are required, as shown below.
Step 2: Use the device, with wall mount plates attached, as a guide to mark the correct locations
of the four screws.
Step 3: Insert a screw head through middle of the keyhole-shaped aperture on the plate, and
then slide the device downwards. Tighten the screw head for added stability.
Version 1.5
Top Panel
3
SIM Card
1. Terminal block
2. Wall-mount screw holes
PWR-2 PWR-1
3. SIM card slot
4. Frame ground
V2- V2+ V1- V1+ DC12-48V
2 1 4
PWR1 PWR2 PoE
LTE
ETH1 ETH2 WIFI Main ANT.
WAN
IMG-4312+-MN
WIFI ANT.
Reset
ETH2
Serial
ETH1
Rx Tx
P.O.E.
10/100M
LTE
AUX ANT.
Quick Installation Guide