Troy-Bilt 10030 Operator's Manual page 19

Safety & Decorative Labels
777D03165
777S32066
AWAY. CLOTHING AND DANGER
FEET HANDS, KEEP
- AUGER ROTATING
1. KEEP AWAY FROM ROTATING IMPELLER
FROM INJURY AVOID AND AUGER. CONTACT WITH IMPELLER OR
AUGER CAN AMPUTATE HANDS AND FEET.
2. USE CLEAN-OUT TOOL TO UNCLOG
DISCHARGE CHUTE.
DISENGAGE CLUTCH LEVERS, STOP ENGINE,
3.
AND REMAIN BEHIND HANDLES UNTIL ALL
MOVING PARTS HAVE STOPPED BEFORE
UNCLOGGING OR SERVICING MACHINE.
TO AVOID THROWN OBJECTS INJURIES,
4.
NEVER DIRECT DISCHARGE AT BYSTANDERS.
USE EXTRA CAUTION WHEN OPERATING ON
GRAVEL SURFACES.
DANGER 5. READ OPERATOR'S MANUAL.
CLEAN-OUT TOOL
Tecumseh Engine Labels
751T642082100
Muffler and adjacent surfaces
are HOT. Do not touch.
AVERTISSMENT
Silencieux et surfaces adjacentes
TRES CHAUDES. Ne pas toucher.
El silenciador y las areas alredador
2082 estan CALIENTES. No tocar.
Top of plastic engine cover
above muffler vents in plastic
777D06563
777D06573
751T64141769
CAUTION
AVERTISSEMENT
POUR VOTRE PROTECTION VEUILLEZ
LIRE ATTENTIVEMENT LES DIRECTIVES
SUR LA SECURITE ET L'ENTRETIEN
DANS LE MANUEL DU PROPRIETAIRE
CUIDADO
On plastic engine cover
left side of electric starter
777D06574
TOUCH 'N TURN STEERING • ALL WHEEL DRIVE • ELECTRIC START • JUST ONE HAND ® OPERATION
777I22052 777I22049
AUGER CONTROL
LEFT TURN
CONTROL
CHUTE
DIRECTIONAL CONTROL
CLOCKWISE TO DISCHARGE LEFT
COUNTER CLOCKWISE TO
DISCHARGE RIGHT
I22052
777S32065
DANGER
NEVER PUT HAND IN CHUTE. CONTACT WITH
ROTATING PARTS CAN AMPUTATE FINGERS
AND HANDS. USE CLEAN-OUT TOOL TO
UNCLOG DISCHARGE CHUTE.
DO NOT UNCLOG DISCHARGE CHUTE WHILE
ENGINE IS RUNNING.
SHUT OFF ENGINE AND REMAIN BEHIND
HANDLES UNTIL ALL MOVING PARTS HAVE
STOPPED BEFORE UNCLOGGING.
D00056
10030
D06573
751T641393
On plastic engine cover
above primer knob
19
D06574
777I22053
6 HEATED
READ OPERATORS MANUAL BEFORE STARTING. TRACTION HANDLE GRIPS
CONTROL
INSERT IGNITION KEY INTO SLOT.
5
MAKE SURE IT SNAPS INTO PLACE.
DO NOT TURN KEY. OFF ON
4 RECOIL STARTER: PUSH PRIMER 2 OR 3 TIMES.
ELECTRIC STARTER: DO NOT PRIME.
PUSH START BUTTON OR PULL ROPE HANDLE
3
TO START ENGINE.
SELECT SPEED REQUIRED. SQUEEZE RIGHT
2 TRACTION CONTROL
TRACTION CONTROL LEVER TO MOVE.
RELEASE TO STOP.
ALWAYS RELEASE TRACTION CONTROL
F 1
LEVER BEFORE CHANGING SPEEDS.
CHUTE
TILT FOR SNOWTHROWING, ENGAGE LEFT AUGER
CONTROL CONTROL LEVER BEFORE TRACTION
CONTROL LEVER.
IMPORTANT: THIS MACHINE IS EQUIPPED WITH AN
R R1 AUGER CONTROL LOCK. TO STOP AUGER,
BOTH AUGER CONTROL AND TRACTION CONTROL
LEVERS MUST BE RELEASED.
RIGHT TURN CONTROL
R2 FOR STEERABLE OPERATION:
SQUEEZE LEFT TURN CONTROL TO STEER
SNOWTHROWER TO THE LEFT. SQUEEZE RIGHT
TURN CONTROL TO STEER SNOWTHROWER
TO THE RIGHT.
TO STOP ENGINE, PULL OUT IGNITION KEY.
I22049
I22053
777I22047
777D06572
PLACE ABOVE INGNITION
CUT OUT
10 HP
®
D06572