EdilKamin KIRA Installation, Use And Maintenance Manual
  1. Manuals
  2. Brands
  3. EdilKamin Manuals
  4. Pellet stove
  5. KIRA
  6. Installation, use and maintenance manual

EdilKamin KIRA Installation, Use And Maintenance Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

KIRA - VYDA
PELLET STOVE
EN
Installation, use and maintenance
page 2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KIRA and is the answer not in the manual?

Questions and answers

Related Manuals for EdilKamin KIRA

Summary of Contents for EdilKamin KIRA

  • Page 1 KIRA - VYDA PELLET STOVE Installation, use and maintenance page 2...

  • Page 2: Table Of Contents

    PELLET STOVE, trade name EDILKAMIN, model KIRA - VYDA SERIAL NO.: Rating plate reference KIRA - VYDA: Performance declaration: (DoP - EK No. 160): Moreover, the company hereby declares that: the KIRA - VYDA wood pellet stove satisfies the requirements...

  • Page 3: Introduction And Who The Manual Is For

    First ignition is required for activation of the Edilkamin manual, observe local regulations. manufacturer warranty. The warranty is only valid in the The diagrams provided in this manual are for illustration country where the product was bought.

  • Page 4: Safety Information

    • Blocking the aeration vents and air intakes in the neither Edilkamin nor the retailer are liable for room. DO NOT BLOCK THE AERATION VENTS damage resulting from incorrect installation or OR FLUE. Risk of smoke returning into the room maintenance.

  • Page 5: Dimensions

    DIMENSIONS KIRA - DIMENSIONS (cm) Ø 8 cm hot air ducting * Ø 4 cm combustion air Ø 8 cm smoke outlet 31,5 31,5 * accessories for ducting hot air are available USER/INSTALLER...
  • Page 6 DIMENSIONS VYDA - DIMENSIONS (cm) 15,5 15,5 Ø 8 cm hot air ducting * Ø 4 cm combustion air Ø 8 cm smoke outlet 15,5 62,5 * accessories for ducting hot air are available USER/INSTALLER...

  • Page 7: Technical Data

    Protection rating Fusibile 4 AT, 250 Vac 5x20 The above data is for guidance only and was measured during certification by a notified body. EDILKAMIN s.p.a. reserves the right to modify the product without notification in the interests of improvement. USER/INSTALLER...

  • Page 8: Unpacking

    (2) with the ceramic or stone cladding • buffers to be applied on top of the grille) * Other small parts (for Vyda and Kira) In the stove package you will find: • M4 screws with washers for fixing the ceramic •...

  • Page 9: Fitting The Cladding Kira

    UNPACKING TO REMOVE KIRA FROM THE PALLET To remove the stove from the pallet you must (see figures below corresponding to instructions): 1. remove the two brackets (screwed) on the front 2. remove the two brackets (screwed) on the rear of the stove...

  • Page 10: Installation

    Contact the authorised Edilkamin Technical Assistance itself, or in any area with an explosive atmosphere. Centre. Any extraction fans operating in the same room or area as the product, may affect its draw.
  • Page 11 INSTALLATION FLUE SYSTEM • be certified, with a chimney plate if metal (Smoke duct, fl ue and chimney pot) • be of uniform cross section or vary in cross section This chapter has been drawn up pursuant to European only immediately after the outlet, not at some mid regulations EN 13384, EN 1443, EN 1856 and EN point of its length.
  • Page 12 INSTALLATION THE FLUE: EXTERNAL AIR INTAKE Further to the general prescriptions for the smoke duct In general, we suggest two ways to ensure a proper and flue, the flue: flow of combustion air. • must serve solely to discharge smoke •...
  • Page 13 (Bent, Split, Origami, Sharp). The instructions for connecting these vents are given in the manual provided with the vents. For Ø 8 cm ducting with Edilkamin Kit 12- 12bis • kit 12 for ducting into an adjacent room (pipe Ø 8 cm -3 m in length, B4 terminal vent;...
  • Page 14 The electrical system must be compliant; check the operation of the earth in particular. Edilkamin is not responsible for malfunctions resulting from an improperly earthed system. The power line must be of adequate section for the power of the appliance.
  • Page 15 The metal grille of the top is in the package of the stove structure together with the M4 screws, fixing washers and the two rubber buffers to be applied on top of the grille * Small parts to be used for Kira : •...
  • Page 16 KIRA - CLADDING Fitting of the bottom front panel (1) THE DRAWINGS ARE FOR GUIDANCE ONLY, USEFUL FOR THE INSTALLATION, BUT THEY MAY NOT REFER TO THE SPECIFIC MODEL. 1. Open the combustion chamber door with the protective lever (removable handle P) and undo two screws to remove the bottom metal front panel 2.
  • Page 17 KIRA - CLADDING Fitting of the top front panel (2) 1. Undo the two upper screws. 2. Remove the metal support (S). 3. Place the top ceramic front panel (2) on the metal support (S). Fit the front panel (2) with the M4 screws provided with washers 4.
  • Page 18 KIRA CLADDING THE DRAWINGS ARE FOR GUIDANCE ONLY, Fitting the ceramic sides (3,4,5,6) USEFUL FOR THE INSTALLATION, BUT The sides are hooked and screwed on top Start from the bottom ceramic part of one of the two sides. THEY MAY NOT REFER TO THE SPECIFIC MODEL.
  • Page 19 KIRA - CLADDING Fitting the ceramic top (7) The top part of the lining consists of a grille (G) for the hot air output and the stone or ceramic top (4). 1. Fit the two rubber buffers provided on the top part of the grille.

  • Page 20: Fitting The Cladding Vyda

    VYDA - CLADDING Description Reference in the Quantity Figure below Front panel above the door (ceramic or stone) Top front panel (ceramic or stone) Left or right interchangeable sides (ceramic or stone) Top (ceramic or stone) The metal grille of the top is in the stove structure package together with the M4 screws (and M6 for the stone top), the fitting washers and the two rubber buffers * Small parts to be used for Vyda : •...
  • Page 21 VYDA - CLADDING THE DRAWINGS ARE FOR GUIDANCE ONLY, Fitting of the stone or ceramic front panel above USEFUL FOR THE INSTALLATION, BUT the door (1) THEY MAY NOT REFER TO THE SPECIFIC MODEL. 1. Open the combustion chamber door with the protective lever (removable handle P) and undo two screws to remove “aesthetic cover”.
  • Page 22 VYDA - CLADDING 3. Refit the “aesthetic cover” aesthetic cover 4. Screw it back with the two screws removed in point INSTALLER...
  • Page 23 VYDA - CLADDING Fitting of the stone or ceramic top front panel 1. undo the two upper screws 2. remove the metal support (S) 3. Place the top ceramic or stone front panel (2) on the metal support (S). Fit the front panel (2) with the screws provided: M4 with washers for the ceramic front panel;...
  • Page 24 VYDA - CLADDING Fitting of the stone or ceramic sides (3) The sides (3) are only hooked on. 1. Place the rubber buffers and hook the sides to the structure Note: see the diagram for correct installation of the ceramic tile rubber buffers To make alignment adjustments between ceramic/ stone and the door, you can move the top or bottom...
  • Page 25 VYDA - CLADDING Fitting of the stone or ceramic top (4) The top part of the lining consists of a grille (G) for the hot air output and the stone or ceramic top (4). 1. Fit the two rubber buffers provided on the top part of rubber buffers the grille.

  • Page 26: Instructions For Use

    Do not use the stove as an incinerator. Caution Using fuels other than those specified can damage the appliance To close the lid of Kira , unhook the hook as shown in the figure below. hook USER...
  • Page 27 USER INSTRUCTIONS OPERATION The stove also has the following supplementary functions. Mode Size settings MANUAL • power level Function In which mode it What it does • ventilation level (the three fans can be activated can be adjusted separately) * STAND BY automatic when the desired...
  • Page 28 In normal use, the remote control’s batteries should last a year. This duration is for illustrative purposes ON/OFF only. Edilkamin and the reseller will not consider claims for battery life under any circumstances. If the battery button charge is low, a warning displays at the top left (see the paragraph on “If problems arise”).
  • Page 29 USER INSTRUCTIONS The display reads the POSSIBLE STATES described below: - OFF STATE The product is shutting down or is off in response to a manual switching off by using the ON/OFF button of the remote control or due to an external contact (crono, phone dialler) The display shows the current time, room temperature and the status in relation to which the product is OFF.
  • Page 30 USER INSTRUCTIONS USER CONTROLS (REMOTE CONTROL) Switching on and off will take a few minutes, - ON/OFF during which the flame must appear or go - Switch-on/switch-off off. Just wait without taking any action. - Manual mode setting During ignition, the display shows the text •...
  • Page 31 “blades” symbol. To ensure that the speed of fans 2 and 3 varies according to the room temperature demand, contact the Edilkamin technician, who will be able to fit dedicated sensors. THE NUMBER NEXT TO THE “BLADE” OR “FLAME” ONLY DISPLAYS WHILE THE SETTING IS BEING MADE.
  • Page 32 USER INSTRUCTIONS - Relax function - Stand by Natural convection function (without ventilation) with When the Stand by function is active, in automatic automatic power limiting. and crono modes, the product shuts off when the This function is available in all modes: automatic, temperature setpoint is reached and turns on again manual and crono.
  • Page 33 USER INSTRUCTIONS - Crono “OK”: confirm the time When the Crono function is active, the user sets a “M” : return to the previous menu temperature setpoint and a time zone for which that ON/OFF: return to the main screen. setpoint is specified.
  • Page 34 USER INSTRUCTIONS - Night Pellet Load This function shuts the product down after a set Allows you to load pellets after the worm screw has number of hours from activation of the function. emptied following a no-pellets alarm. Used by the technician during commissioning. this is convenient if you go to bed and want the product Available only in the OFF state.
  • Page 35 USER INSTRUCTIONS Date/Time Beep Sets the current date/time. Allows you to enable/disable the beep. This displays the first time the remote control is To access the function from the main menu (as activated with the stove powered on, or by selecting indicated in the Menu section above), press the M the option in the menu.

  • Page 36: Maintenance

    MAINTENANCE Disconnect the product from the power supply. Failure to service the product properly will prevent it from working properly. Any problems due to failure in servicing the stove will void the warranty. Using the stove without cleaning the grate can cause the gas in the combustion chamber to ignite and detonate.
  • Page 37 MAINTENANCE • Do not dump the cleaning residue into the pellet tank. • Once it is refitted, make sure that the ash tray is properly placed in its housing, to avoid glass breakage when closing. • Make sure that the grate is properly placed in its housing after maintenance operations, if not, the stove may have ignition problems.
  • Page 38 MAINTENANCE WEEKLY MAINTENANCE When the product is off and cold, after having routine maintenance, you should vacuum the inspection plate under the combustion chamber (*) To do so: • Remove the protection, by turning the winget nut (V) • remove the deflector (D) which is only resting on it. Put back the deflector after cleaning.
  • Page 39 MAINTENANCE Remove the deflector and vacuum clean. Put back in position with care by placing it in its housing. deflector deflector USER/INSTALLER...
  • Page 40 You should clean the chimney system at least once a Using non-original spare parts may damage the year (check local regulations for details). appliance and relieves Edilkamin of all liability for damage resulting there from. If you fail to regularly clean and inspect the system, Do not make unauthorised modifi...

  • Page 41: Troubleshooting

    TROUBLESHOOTING If problems occur, the product shuts itself off automatically. The display will show the reason (see below). Do not disconnect from the power supply. To start the product up again, allow the shutdown procedure to complete, then press the remote control’s ON/OFF button or the simplifi...
  • Page 42 The battery symbol will appear on the remote control display if the battery is low. MAINTENANCE: A wrench symbol is shown on the display after 2000 hours of operation. The product is working, but it must be serviced by an authorised Edilkamin technician. USER/INSTALLER...
  • Page 44 *941649-GB* w w w . e d i l k a m i n . c o m cod. 941649-GB 10.17/C...

This manual is also suitable for:

Vyda

Table of Contents