PPI LabCon Ultra Operation Manual

LabCon Ultra
Multi-Purpose Temperature Controller
with Recording & PC Software
Level Sub-Level Parameters
Temperature Set Value
Temperature
Low Deviation Alarm
Temperature
High Deviation Alarm
SP Edit on Home Screen
Operator
Timer Start / Abort Command
Time Interval (HH:MM)
Zero Offset
Recording Interval
Recording
'Delete Record' Command
Calendar Date (DD/MM/YY)
Clock Time (HH:MM:SS)
Clock & Calendar
Set Value
(Temperature Control Loop)
Low Limit
(for Temp. Control Set Value)
High Limit
(for Temp. Control Set Value)
Overshoot Inhibit
Cutoff Factor
Control PV Strategy
Self Tune
Compressor SP
Supervisory
Cool Hysteresis
Control Settings
Heat Zone PID Constants
Heat Zone Proportional Band
Heat Zone Integral Time
Heat Zone Derivative Time
Cool Zone PID Constants
Cool Zone Proportional Band
Cool Zone Integral Time
Cool Zone Derivative Time
Proportional Band
Integral Time
Derivative Time
Single Zone & Dual Zone
Output Cycle Time (Sec.)
This brief manual is primarily meant for quick reference to wiring connections and parameter
searching. For more details on operation and application; please log on to www.ppiindia.net
Range
Level
(Default)
Temp. Setpoint Low Limit
to Temp. Setpoint High Limit
(Default : 25.0 °C)
SMS Alert
0.2 to 99.9 °C
(Default : 2.0 °C)
0.2 to 99.9 °C
Maintenance
(Default : 2.0 °C)
Supervisory
Enable
Disable
Standby Switching
NA
0.00 to 500.00
(Default : 0.10)
Door Lock Access
-50.0 to 50.0°C
(Default : 0.0°C)
0 to 250 Minutes
(Default : 5 Minutes)
NA
NA
NA
Temp. Setpoint Low Limit to
Temp. Setpoint High Limit
(Default : 25.0)
-199.9 to Temperature
Setpoint High Limit
(Default : 10.0)
For RTD : Temperature Setpoint
MAP-0 Sensor
Low Limit to 600.0
For mA/V : Temperature Setpoint
Low Limit to 999.9
(Default : 60.0)
Enable
Disable
(Default : Disable)
1.0 to 2.0
(Default : 1.2)
Factory
MAP-0 PV, Average PV if
MAP-0 Fails, Average PV
(Default : MAP-0 PV )
NA
0.0 to 100.0
(Default : 45.0)
0.1 to 99.9
(Default : 2.0)
Dual Zone
0.1 to 999.9 °C Heat-Cool Select
(Default : 50.0 °C)
0 to 3600 Sec.
(Default : 100 Sec.)
0 to 600 Sec.
(Default : 16 Sec.)
0.1 to 999.9 °C
(Default : 50.0 °C)
Alarm Settings
0 to 3600 Sec.
(Default : 100 Sec.)
0 to 600 Sec.
(Default : 16 Sec.)
Single Zone
0.1 to 999.9 °C
(Default : 50.0 °C)
0 to 3600 Sec.
(Default : 100 Sec.)
Timer
0 to 600 Sec.
(Default : 16 Sec.)
0.5 to 100.0 Sec.
(Default : 10.0 Sec.)
Operation Manual
Sub-Level Parameters
(Default)
GSM Machine ID
(Default : 1)
SMS
Reset GSM Module
Repair Acknowledge
'Control Gadget'
'Switch Main/Standby Outputs'
Lock Position (On / Off) Solenoid ON
Solenoid OFF
(Default : Solenoid OFF)
Password Entry
Input Type TC-J, TC-K, TC-P, TC-R,
TC-S, TC-B, TC-N,
RTD Pt100, 0 to 20 mA,
4 to 20 mA, 0 to 5 V,
0 to 10 V, 1 to 5 V
(Default : RTD Pt100)
Signal Range Low
Input Type
0 to 20mA
4 to 20mA
0 to 5V
0 to 10V
1 to 5V
Signal Range High
Input Type
0 to 20mA
4 to 20mA
0 to 5V
0 to 10V
1 to 5V
Display Range Low -199.9 to Range High
(Default : 0.0)
Display Range High Range Low to 999.9
(Default : 100.0)
Zero Offset -50.0 to 50.0°C
(Default : 0.0°C)
Mode
Continuous OFF, Continuous ON,
SP Based ON-OFF, PV Based ON-OFF
(Default :
Time Delay 0 to 1000 Sec.
(Default : 200 Sec.)
Boundary SP 0.0 to 100.0
(Default : 45.0)
Zone Select Single, Dual
(Default : Singlel)
Inhibit Enable, Disable
(Default : Enable)
Low Alarm Deviation 0.2 to 99.9
High Alarm Deviation
(Default : 2.0)
Hysteresis
0.1 to 99.9
(Default : 0.2)
Timer
(Default : Disable)
On Timer END
(Default : Yes)
Heater Off
On Timer END
Compressor Off (Default : Yes)
Hold Band Type None, Up, Down, Both
(Default : None)
Hold Band Value 0.1 to 999.9
(Default : 0.5)
Start Band Value
Default : 0.5
Power Up recovery Abort, Restart, Continuous
Default : Abort
Range
Level Sub-Level
1 to 128
NA
Power Fail
NA
NA
Door Open
NA
Configuration
Settings Default
0.00 to
0.00
Signal High
4.00 to
4.00
Signal High
0.000 to
0.000
Signal High
0.00 to
0.00
Signal High
1.000 to
1.000
Signal High
Factory
Settings
Default
Signal Low
20.00
to 20.00
Signal Low
20.00
Mapping
to 20.00
Signal Low
5.000
to 5.000
Signal Low
10.00
Input Settings
to 10.00
Signal Low
5.000
to 5.000
Continuous OFF )
Standby
Control Settings
Enable
Disable
Yes / No
Yes / No
0 to 999.9
101, Diamond Industrial Estate, Navghar, Vasai Road (E), Dist. Palghar - 401 210.
T: 0250 - 2391722/33/37/42 M: 07498799226 / 09321985369
E: sales@ppiindia.net, support@ppiindia.net
Aug 2019
Range
Parameters
(Default)
Detection Enable No / Yes
(Default : No)
Power Fail Logic Switch Open, Switch Close
(Default : Switch Close)
Detection Enable No / Yes
(Default : No)
Door Open Logic Switch Open, Switch Close
(Default : Switch Close)
Alarm Delay (Sec.) 0 to 1000 Sec.
(Default : 60 Sec.)
Select Mapping Inputs 1 MAP (M0),
2 MAP (M0+M1),
3 MAP (M0+M1+M2),
4 MAP (M0+M1+M2+M3),
5 MAP (M0+M1+M2+M3+M4)
(Default : 1 MAP (M0)
Input Type TC-J, TC-K, TC-P, TC-R,
TC-S, TC-B, TC-N,
RTD Pt100, 0 to 20 mA,
4 to 20 mA, 0 to 5 V,
0 to 10 V, 1 to 5 V
(Default : RTD Pt100)
Signal Range Low
Input Type Settings
Default
0.00 to
0 to 20mA 0.00
Signal High
4.00 to
4 to 20mA 4.00
Signal High
0.000 to
0 to 5V 0.000
Signal High
0.00 to
0 to 10V 0.00
Signal High
1.000 to
1 to 5V 1.000
Signal High
Signal Range High
Input Type Settings Default
Signal Low
0 to 20mA 20.00
to 20.00
Signal Low
4 to 20mA 20.00
to 20.00
Signal Low
0 to 5V 5.000
to 5.000
Signal Low
0 to 10V 10.00
to 10.00
Signal Low
1 to 5V 5.000
to 5.000
Display Range Low -199.9 to Range High
(Default : 0.0)
Display Range High Range Low to 999.9
(Default : 100.0)
Fail Detect Time (Min) 0 to 250 Min.
(Default : 10 Min.)
Cyclic Time (Hrs.) 0 to 500 Hrs.
(Default : 48 Hrs.)
Inhibit Time (Hrs.) 0 to 250 Hrs.
(Default : 1 Hrs.)
Heater Output Type SSR
(Main & Standby Heater) 0-20 mA
0-4 mA
0-5 V
0-10 V
(Default : SSR)