Related Manuals for Willow Milk Container
Summary of Contents for Willow Milk Container
- Page 1 Willow Wearable Breast Pump Milk Container Quick Start Guide...
- Page 2 For complete Instructions for Use, visit willowpump.com...
- Page 3 Your Milk Container comes assembled, but has two parts - the Insert and Container. Insert Container Dial Air Vent Unlocked Position (underneath Dial) Locked Position Spout Locking Ring Dial Tunnel Interior Valve Pour Spout Front Back...
- Page 4 set dial to 1 to pump... Rotate Dial so only the 1 is visible (and the 2 is hidden under Cap). ‘1’ = Pump • Set Dial to 1 (Pump position) at the start of your session • This keeps the air vent open when you pump Rotate all the way until...
- Page 5 ...and 2 when you’re done! Rotate Dial so only the 2 is visible (and the 1 is hidden under Cap). ‘2’ = Flip to Finish • Set Dial to 2 (Flip to Finish position) when you’re finished pumping • This closes the air vent for Flip to Finish •...
- Page 6 1. Disassemble Milk Container Rotate blue Push hard on Insert Separate Peel back locking ring to tunnel (use both thumbs!) Container and unlocked position until it pops out Insert 2. Boil Container and Insert for ten minutes to sterilize before you use it (just for the first time!).
- Page 7 get ready to pump Just 4 parts - and you’re ready to pump! Insert Container Flextube™ Pump...
- Page 8 assemble container insert & Place Insert into Press firmly to Rotate to Make sure Container (tab facing up) seal to Container locked position Cap is closed...
- Page 9 Rotate Dial so only Push Flextube™ Connect Flextube™ tip the 1 is visible (and the collar in so it sits firmly to Insert spout. 2 is under Cap) against Cap Push tip all the way down!
- Page 10 Turn Pump on and bring straight on to Center your nipple in Milk Container with your other hand to the Insert tunnel. connect. Press Play to initiate latch. For more on alignment, pumping, and breaking latch, visit: willowpump.com for Willow Wearable Breast Pump Instructions for Use...
- Page 11 (stay dry!) • The air vent (on the top of the Milk Container) is Get up open while you pump. and pump... • To avoid leaks, make sure milk doesn’t cover the air vent when you pump. • To pump in any position, pump with our spill-proof Milk Bags.
- Page 12 Rotate so Cap 2 (Flip to Finish position) to close remove Pump faces you air vent - or milk will leak! TIP: Rotate Dial to 2 (Flip to Finish position) before you remove Willow from your bra to avoid spills.
- Page 13 then flip to finish TILT until pump starts to gulp HOLD until milk disappears from tunnel FLIP all the way over and wait Watch videos in app or until gulps stop (a total of 8 gulps) at willowpump.com...
- Page 14 Separate Milk Flip Pump over so Container from Pump Milk Container faces up Pour from pour Open Cap spout on top Always keep Container and Insert assembled to pour.
- Page 15 Separate Flextube™ from Milk Container to clean, then follow instructions on p. 4 to disassemble into parts below. Insert Container TIP: You can leave the Cap on or remove it to clean. Make sure the Cap is open if you leave it on.
- Page 16 ❏ Soak in warm, soapy water for a minimum of 5 minutes (use mild dishwashing soap, and agitate while they soak). ❏ Use the Large Cleaning Brush from your Willow Pump Kit to clean (wash for at least 60 seconds, minimum 30 seconds of brushing).
- Page 17 Scrub around interior valve - don’t push a brush through it!
- Page 18 & lights Willow’s lights tell you what’s going on with your Milk Container. Here’s what they mean. White Solid: Your Container is full. Flip to Finish (see p. 10-11), transfer to a bottle or bag, then press Pump/Pause to continue pumping.
- Page 19 1-888-WILLOW-3 care willowpump.com willowpump.com/help...
- Page 20 ©2019 Willow. All rights reserved. Willow and Flextube are trademarks or registered trademarks of Willow in the United States and other countries.
Need help?
Do you have a question about the Milk Container and is the answer not in the manual?
Questions and answers