Download Print this page
Pakedge WA-2200 Quick Start Manual

Pakedge WA-2200 Quick Start Manual

802.11ac 2x2 wave 2 access point
Hide thumbs Also See for WA-2200:

Advertisement

Quick Links

WA-2200, WA-2200-1
802.11ac 2x2 Wave 2 Access Point
BakPak
Lite
QUICK START GUIDE

Advertisement

loading
Need help?

Need help?

Do you have a question about the WA-2200 and is the answer not in the manual?

Questions and answers

Summary of Contents for Pakedge WA-2200

  • Page 1 WA-2200, WA-2200-1 802.11ac 2x2 Wave 2 Access Point BakPak Lite QUICK START GUIDE...
  • Page 2 WA-2200 features • 802.11ac dual-band 2×2 wireless technology • Advanced Wave 2 wireless technology with MU-MIMO and beamforming • Powered by PoE (or optional 12VDC 1A power adapter, sold separately) • Single- to multi-AP cloud configuration with built-in BakPak Lite •...
  • Page 3: Mounting On A Ceiling

    Mounting on a ceiling 1 Tape the included template against the desired mounting location, then mark the places to drill mounting holes and install the appropriate mounting hardware. T-Bar T-Bar Mounting Screw Mounting Screw Wall Bracket Wall Bracket For use with For use with Mounting Anchors Mounting Anchors...
  • Page 4 Removing the AP from the bracket To remove the AP from the bracket: 1 While pressing the AP against the bracket, slide the AP up slightly, then pull it away from the bracket. Powering up The AP can be powered by either PoE or the optional AC power adapter (sold separately).
  • Page 5: Logging In To The Access Point

    To log in to the access point: 1 Connect the access point to your PoE switch with an Ethernet cable. 2 Log in to your Pakedge router to find the IP address assigned to the access point under the DHCP Client Table.
  • Page 6 5 Enter and verify a new username and password (required) before continuing, then click Apply to complete the setup. Caution: For international models, you must change the Country Code (a drop-down list defaulting to GB - United Kingdom), to the specific country of operation.
  • Page 7 Registering your device with BakPak Lite You can connect your access point to your existing BakPak account or create a new account to manage all of your BakPak network management agents. To register your device to your BakPak account: 1 In the device’s Connections tab, to the right of the “This product is not managed by BakPak”...
  • Page 8 To begin managing and configuring the AP, you need to create a BakPak site for it. To create a BakPak site: 1 Log in to your BakPak account, then click Add Site to create a site. 2 In the Management Agent list, select the first WA-2200, complete the site information, then click OK.
  • Page 9 Adding WA Series APs to the site After the BakPak site is created, the WA-2200 will act as the “master AP” for adding more WA Series APs to the site. To add APs and provision them with the existing configuration:...
  • Page 10 4 To apply the master AP’s settings to the new APs, in the BakPak site select the master AP, then complete the site information and click Save & Apply Multiple at the bottom. The settings are copied to the new APs.
  • Page 12: Technical Support

    Technical Support For technical help: www.pakedge.com/portal support@pakedge.com (650) 385-8703 For regulatory information: www.pakedge.com/regulatory Latest version at pkdge.co/wa2200-qsg 11734 S. Election Road Draper, UT 84020 Main: (650) 385-8700 Fax: (650) 685-5520 www.pakedge.com sales@pakedge.com 200-00575-D 2019-04-30 MS ©2019 Control4. All rights reserved.

This manual is also suitable for:

Wa-2200-1