Advertisement
Quick Links
SOP for CCTVs in SunGuide
BOSCH AutoDome 800 HD
This Standard Operating Procedure is to provide a standard configuration for CCTV cameras in
District 5 for consistent operation in SunGuide, VLC and IVEDDS. Standard settings to check:
Network settings, Video/Encoder settings, SNTP (time server type), IP addresses, PTZ settings,
Date and Time, RTSP port, NTCIP (port and address), and On Screen Display (ODS).
The following SOP is for the BOSCH AutoDome 800 HD (820) IP camera.
Log into the camera, using Internet Explorer or Chrome to access the camera's user interface.
Type in the default IP address.
Advertisement
Related Manuals for Bosch AutoDome 800 HD
Summary of Contents for Bosch AutoDome 800 HD
- Page 1 Date and Time, RTSP port, NTCIP (port and address), and On Screen Display (ODS). The following SOP is for the BOSCH AutoDome 800 HD (820) IP camera. Log into the camera, using Internet Explorer or Chrome to access the camera’s user interface.
- Page 2 SOP for CCTVs in SunGuide Click on “Settings”. Click on “Advanced Mode”.
- Page 3 SOP for CCTVs in SunGuide Click on “Service”. Click on “Maintenance”. Browse and Upload the provided Firmware file for the camera. Click on “Service”. Click on “System Overview”. Check the System to see if the Firmware was loaded.
- Page 4 SOP for CCTVs in SunGuide Click on “Network”. Click on “Network Access”.
- Page 5 SOP for CCTVs in SunGuide NOTE: Click SAVE after every configuration setting for that window before moving to the next menu item. 1. Network settings: Set the following parameters for the “Network Access”. DHCP is disabled <Off> IP address <10.X.X.X> Subnet mask <255.255.255.X>...
- Page 6 SOP for CCTVs in SunGuide Click “Set and Reboot”. After Reboot, log into the camera, use Internet Explorer or Chrome to access the camera’s user interface. Type in the assigned IP address.
- Page 7 SOP for CCTVs in SunGuide Click on “Settings”. Click on “Advanced Mode”. Click on “Network.” Click on “Advanced.” Set the following parameters for the “Advanced” setting. SNMP: < On > RTSP Port: < 554 > NTCIP Port: < 4439 > NTCIP Address: <...
- Page 8 SOP for CCTVs in SunGuide Click Set. Click on “Advanced Mode”. Click on “Network.” Click on “Multicast” Set the following parameters for the “Multicast” setting Stream 1 and Stream 2. Enable: < check box > Multicast Address: < If provided 232.219.X.X > Port: (Stream 1) <...
- Page 9 SOP for CCTVs in SunGuide Click Set. Click on “Advanced Mode”. Click on “General”. Click on “Identification”. Type the Camera Name or Camera Location. Camera name: <Example: I-95 NB AT MM 000.0>...
- Page 10 SOP for CCTVs in SunGuide Camera name: <Example: SR 50 at JYP> Click Set. Click “Date/Time”. Set the following parameters for the “Date/Time”. Date format: < MM/DD/YYYY> Device Time Zone: < Select (UTC -5:00) Eastern Time > Device Time format: <...
- Page 11 SOP for CCTVs in SunGuide Camera name stamping: < Top> Camera OSD: < On > Click Set. 2. Camera Video/Encoder settings: Click on “Camera”. Click on “Encoder Profile”.
- Page 12 SOP for CCTVs in SunGuide Click on “Profile 6”. Set the following parameters for the Profile 6 Tab. Profile name: < iVEDDS > Target bit rate: < 500 kbps> Maximum bit rate: < 1100 kbps> Video resolution: < 240p >...
- Page 13 SOP for CCTVs in SunGuide Click Expert Settings. GOP Structure: <IBBP> Click Set.
- Page 14 SOP for CCTVs in SunGuide Click on “Profile 8”. Set the following parameters for the Profile 8 Tab. Profile name: < ITS > Target bit rate: < 1500 kbps> Maximum bit rate: < 6000 kbps> Video resolution: < 240p > Click Set.
- Page 15 SOP for CCTVs in SunGuide Click on “Encoder Streams”. Set the following parameters for the “Encoder Streams”. Property Stream 1: < H.264 MP 720p25/30fixed > Non-recording profile: < 8: ITS > Property Stream 2: < H.264 MP SD > Non-recording profile: <...
- Page 16 SOP for CCTVs in SunGuide Click on “Camera Settings”. Ensure that the following parameters for the “Camera Settings” are set.
- Page 17 SOP for CCTVs in SunGuide Click on “Lens Settings”. Ensure that the following parameters for the “Lens Settings” are set.
- Page 18 SOP for CCTVs in SunGuide Click on “PTZ Settings”. Ensure that the following parameters for the “PTZ Settings” are set.
- Page 19 SOP for CCTVs in SunGuide Click on LivePage and PTZ camera. Log out of camera.