Download Print this page
Acuity Brands LITHONIA LIGHTING PRECISE LRP ELN Series Installation Instructions Manual

Acuity Brands LITHONIA LIGHTING PRECISE LRP ELN Series Installation Instructions Manual

Recessed emergency edge lit led exit signs, recessed emergency rough-in sections

Advertisement

Quick Links

RECESSED EMERGENCY EDGE LIT LED EXIT SIGNS
RECESSED EMERGENCY ROUGH-IN SECTIONS
SERIES ELA LRIS 120/277 ELN, ELA 120/277 ELN
CAUTION: For safety and proper operation, read and follow instructions carefully before installation.
This sign shall be installed only where there is adequate
color contrast between the sign legend and the
interior wall finish behind the sign, to provide for
sufficient visibility.
EMERGENCY LIGHTING SYSTEMS
TEL: 800-334-8694 Fax: 770-981-8141 www.lithonia.com
INSTALLATION INSTRUCTIONS
PRECISE
C O L L E C T I O N
SERIES LRP ELN, LRP2 ELN
AND
®
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
WARNING:
FAILURE TO FOLLOW THESE INSTRUCTIONS
AND WARNINGS MAY RESULT IN DEATH, SERIOUS INJURY
OR SIGNIFICANT PROPERTY DAMAGE - For your protection,
read and follow these warnings and instructions carefully before
installing or maintaining this equipment. These instructions do
not attempt to cover all installation and maintenance situations.
If you do not understand these instructions or additional informa-
tion is required, contact Lithonia Lighting or your local Lithonia
Lighting distributor.
WARNING:
RISK OF ELECTRIC SHOCK – NEVER CON-
NECT TO, DISCONNECT FROM OR SERVICE WHILE EQUIP-
MENT IS ENERGIZED.
WARNING:
DO NOT USE ABRASIVE MATERIALS, OR
OTHER SOLVENTS. USE OF THESE SUBSTANCES MAY
DAMAGE FIXTURE, WHICH MAY RESULT IN PERSONAL
INJURY.
WARNING:
RISK OF PERSONAL INJURY – This product
may have sharp edges. Wear gloves to prevent cuts or
abrasions when removing from carton, handling, installing and
maintaining this product.
• Before wiring to power supply, turn off electricity at fuse or circuit
breaker.
• Disconnect A.C. power before servicing.
• All servicing should be performed by qualified personnel.
• Consult your local building code for approved wiring and installa-
tion.
• Do not use outdoors.
• Do not mount near gas or electric heater.
• When back-mounted, fixture must be grounded to avoid potential
electric shock.
• Equipment should be mounted in locations and at heights where
it will not readily be subjected to tampering by unauthorized
personnel.
• The use of accessory equipment not recommended by the manu-
facturer may cause an unsafe condition.
• Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS
AND DELIVER TO OWNER
AFTER INSTALLATION

Advertisement

loading
Need help?

Need help?

Do you have a question about the LITHONIA LIGHTING PRECISE LRP ELN Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Acuity Brands LITHONIA LIGHTING PRECISE LRP ELN Series

  • Page 1 INSTALLATION INSTRUCTIONS ® PRECISE C O L L E C T I O N RECESSED EMERGENCY EDGE LIT LED EXIT SIGNS SERIES LRP ELN, LRP2 ELN RECESSED EMERGENCY ROUGH-IN SECTIONS SERIES ELA LRIS 120/277 ELN, ELA 120/277 ELN CAUTION: For safety and proper operation, read and follow instructions carefully before installation. IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS...
  • Page 2: Parts Description

    Figure 1 PARTS DESCRIPTION COVER CAN GREEN GROUND SCREW TRIM RING MOUNTING SCREW ELECTRONIC CHASSIS BAR HANGER BRACKET TRIM RING HALF CHASSIS SCREW BAR HANGER BRACKET SCREWS PANEL ASSEMBLY BATTERY TYPICAL CONDUIT KNOCKOUT RECESS MOUNTING PLATE INVERTER/CHARGER BOARD BAR HANGER LOCKING SCREW CAPTIVE MOUNTING SCREW TEST SWITCH PLUG ASSEMBLY ALTERNATE MOUNTING HOLES...
  • Page 3 , 10 Figure 2 Ceiling Mount NOTE: If painting or plastering after trim ring is installed, mask mounting holes on trim ring. Tape provided in prepack. CLOSE-IN INSTALLATION: ROUGH-IN SECTION DRY CEILING: (Ref: Fig. 1 and 2) Cutout hole in ceiling material should not exceed 4 1/2" x 13 CEILING MOUNT 3/4"...
  • Page 4 INSTALLATION: ROUGH-IN SECTION (Ref: Fig. 1 and 3) BACK MOUNT NOTE: Wall mount retainers must be used when back mounting Bar hangers are adjustable from 14 " to 24". Position the rough-in section with the side flanges of the cover can flush with the inner (stud side) surface of wall material.
  • Page 5 Figure 6 End Mount CLOSE-IN: INSTALLATION:ROUGH-IN SECTION (Ref: Fig. 1 and 6) DRY WALL: Cutout hole in ceiling material should not exceed 4 1/2" x 13 END MOUNT (Requires End Mount Panel Assembly) 3/4" (max.). Note: The top of the cover can may be used as Remove bar hanger bracket screws and relocate bar...
  • Page 6: Battery Replacement

    WIRING INSTRUCTIONS AND DIAGRAMS Cap all unused leads separately Wiring Diagram WIRING: INVERTER/CHARGER BOARD Select and remove desired knockout for AC power input and ensure adequate lengths of AC power leads extending into REPLACEMENT: inside of cover can Remove recess mounting plate , and lamp assembly Connect AC power supply according to proper wiring from rough-in section by unscrewing two captive mounting...

This manual is also suitable for:

Lithonia lighting precise lrp2 eln seriesLithonia lighting precise ela lris 120/277 eln seriesLithonia lighting precise ela 120/277 eln series