Hoshizaki IM-240DNE Installation Manual
Modular cuber
Hide thumbs
Also See for IM-240DNE:
- Installation manual (88 pages) ,
- Service manual (81 pages) ,
- Instruction manual (26 pages)
Advertisement
Quick Links
MODULAR CUBER
MACHINE A GLAÇONS MODULAIRE
MODULARER WÜRFELEISBEREITER
IJSBLOKJESMACHINE MET LOSSE OPSLAGBUNKER
FABRICADOR MODULAR DE CUBITOS DE HIELO
CUBETTATRICE MODULARE
INSTALLATION MANUAL
NOTICE D'INSTALLATION
INSTALLATIONSANLEITUNG
INSTALLATIE VOORSCHRIFT
MANUAL DE INSTALACION
MANUALE PER L'INSTALLAZIONE
FOR QUALIFIED INSTALLER ONLY
RESERVE A L'INSTALLATEUR
FÜR DEN INSTALLATEUR
VOOR DE BEVOEGDE INSTALLATEUR
SOLAMENTE PARA INSTALADOR CUALIFICADO
SOLTANTO PER INSTALLATORI QUALIFICATI
IM-240DNE
IM-240XNE
IM-240DWNE
IM-240XWNE
IM-240DSNE
IM-240XSNE
IM-240DNE-C
IM-240XNE-C
IM-240DWNE-C
IM-240XWNE-C
L2E1CK201 (060110)
Advertisement
Related Manuals for Hoshizaki IM-240DNE
Summary of Contents for Hoshizaki IM-240DNE
- Page 1 IM-240DNE MODULAR CUBER IM-240XNE MACHINE A GLAÇONS MODULAIRE IM-240DWNE MODULARER WÜRFELEISBEREITER IM-240XWNE IJSBLOKJESMACHINE MET LOSSE OPSLAGBUNKER IM-240DSNE FABRICADOR MODULAR DE CUBITOS DE HIELO IM-240XSNE CUBETTATRICE MODULARE IM-240DNE-C IM-240XNE-C IM-240DWNE-C INSTALLATION MANUAL IM-240XWNE-C NOTICE D’INSTALLATION INSTALLATIONSANLEITUNG INSTALLATIE VOORSCHRIFT MANUAL DE INSTALACION MANUALE PER L’INSTALLAZIONE...
- Page 2 50 cm at the right side (air-cooled model) or 15 cm clearance at rear, sides and top (water-cooled model) for proper air circulation and ease of maintenance and/or Note: This icemaker needs a Storage Bin. Hoshizaki recommends the service should they be required. following Ice Storage Bins: B801SA (Top Kit IMD) -------IM-240D/IM-480D/IM-720D 5.
-
Page 3: Installation
ENGLISH 3. INSTALLATION 2) Remove the icemaker panels. The Rear Panel is not required to be removed for installation. See “1. UNPACKING”. * Incorrect installation can cause 3) Attach the lower unit (X-type) on the top of the Storage Bin. See harm to people, animals or things, Bottom Fig. -
Page 4: Water Supply And Drain Connections
Note: If stacking three icemakers, repeat the instructions 6) - 11) for Supply of replacement fuse covers can be obtained from Hoshizaki the upper unit. Remember, only ONE Bin Control is needed Parts/Service Centres. - Page 5 ENGLISH [Water-Cooled Model] * Hoshizaki recommends that the water-cooled Condenser should be connected to a closed circuit recirculating type cooling system Water Inlet (IM-720) utilizing a tower, water chiller or similar (see Fig. 15 and 16). Water *Cooling Water Inlet make up should be via a ball valve/break tank arrangement.
-
Page 6: Start-Up Procedure
ENGLISH 7. START-UP PROCEDURE Icemaker Potable Water 1) Open the water tap. Inlet G3/4 Cooling Water 2) Connect the power supply and energise. Inlet Rc1/2 1/2-3/4 3) The Display indicates “on”. Nipple Cooling Water Outlet Rc1/2 4) The following should occur in sequence: a) Hot Gas Valve will open.