Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Nokta MAKRO Simplex+
Summary of Contents for Nokta MAKRO Simplex+
- Page 3 ► Protect the detector against impacts during normal use. For shipping, carefully place detector in original carton and secure with shock resistant packaging. ► SIMPLEX+ metal detector may only be disassembled and repaired by Nokta Makro Authorized Service Centers. Unauthorized disassembly/intrusion into the metal detector control housing for any reason voids the warranty.
-
Page 4: Table Of Contents
TABLE OF C ONT EN TS ASSEMBLY ......................................................INTRODUCTION TO THE DEVICE ................................. DISPLAY ........................................................BATTERY INFORMATION ........................................WIRELESS HEADPHONE INFORMATION ..........................CORRECT USE ..................................................QUICK GUIDE .................................................... TARGET ID ......................................................SEARCH MODES ................................................SENSITIVITY ....................................................TARGET DEPTH ................................................SETTINGS 11-15 ...................................................... -
Page 5: Assembly
ASSEMB LY (1) After inserting the washers on the lower shaft, place the lower shaft in its location on the search coil. Secure by tightening the screw and nut. Do not overtighten. (2) To join the middle rod with the upper and lower rods, open the lever latches and engage the pieces together. -
Page 6: Introduction To The Device
INT RODU CT ION TO T HE DE VI CE Settings button to access all settings Pinpoint / Confirm button Down Arrow: On-Off/Hard Reset/Sensitivity Decrease To turn the device on and off press and hold down for about 3 seconds. For a hard reset in case of any unresponsiveness of the system, press and hold down for about 6 seconds. -
Page 7: Display
DISP LAY (1) Target ID scale Shows the ID of the detected target on the ID scale. It also indicates the IDs filtered by Notch Discrimination setting. (2) Search Modes (3) Sensitivity Indicator (4) Section which shows the Target ID upon target detection, pinpoint mode as well as the warning icons. -
Page 8: Battery Information
Do not expose the device to extreme temperatures (for example a car's trunk or glove compartment) Do not charge the battery in temperatures over 35° C (95° F) or below 0° C ( 32° F). The SIMPLEX+ battery can only be replaced by Nokta Makro Detectors or its authorized service centers. -
Page 9: Correct Use
CORREC T U S E Shaft height is wrong Shaft height is correct It is very important to adjust the shaft to your Adjust the height of the shaft so that you are height correctly to be able to search without standing in an upright position, your arm is discomfort and fatigue. -
Page 10: Quick Guide
QU ICK GU IDE 1) Assemble the device as per the instructions on page 1. 2) Push the on/off button to turn on the device. 3) When the device is turned on, it will start in the 2-tone Field mode. You can change the mode based on ground conditions. -
Page 11: Target Id
TARGET ID TARGET ID is the number produced by the metal detector based on the conductivity of the metals and gives an idea to the user about what the target may be. Target ID is shown with two digits on the display and ranges between 00-99. -
Page 12: Search Modes
SE A RCH MO DES SIMPLEX+ has 5 search modes designed for different terrains and targets. You can navigate between the modes easily by using the right and left arrow buttons. The selected mode will be highlighted in black. Field Recommended especially for relic hunting. - Page 13 SE A RCH MO DES All Metal Different than the other modes, this mode features a threshold tone which is continuously heard in the background. You cannot search in the All Metal mode without ground balancing. In this mode, the device does not discriminate targets and detects them all (metals, mineralized rocks etc.).
-
Page 14: Sensitivity
SE N S IT IVIT Y Sensitivity is the depth setting of the device. It is also used to eliminate the ambient electromagnetic signals from the surrounding environment and noise signals transmitted from ground. NOTE: To obtain maximum depth performance, to eliminate the noise caused by electromagnetic interference, try shifting the frequency first. -
Page 15: Settings
SE T TI NGS Push the settings button to access all settings. When settings button is pressed, the volume setting, which is the first setting on the settings bar located at the bottom of the screen, will be highlighted in black. Each time you press the settings button, the next setting on the bar will be selected and its value will be displayed on screen. - Page 16 SE T TI NGS 5. If you cannot ground balance, in other words, if no beep sound is produced, it means that either the ground is too conductive or not mineralized or there is a target right below the search coil. In such a case, retry ground balance at a different spot.
- Page 17 SE T TI NGS Ground Balance Value Ground balance value provides information about the ground you are searching on. Some typical ground types are as follows: 0-25 Wet salt water or wet alkali soils 25-50 Wet salt water and wet alkali soils covered with dry layers 50-70 Regular, low-quality soils 70-90...
- Page 18 SE T TI NGS Manual: 1. Press the settings button and then select notch discrimination in the settings bar. An X and a check mark will appear on screen along with a small arrow cursor underneath the ID bar at the top of the screen. 2.
-
Page 19: Pinpoint
SE T TI NGS Vibration This feature provides feedback to the user by producing a vibration effect when a target is detected. It can be used independently or together with the audio response. When audio response is disabled, all responses during target detection are provided to the user as vibration only. When the vibration is turned on, the device provides short vibration signals upon target detection. -
Page 20: Mute Function
To perform pinpoint: 1) After a target is detected, move the search coil aside where there is no target response and push the pinpoint button. 2) Keep the button pressed down and bring the search coil closer to the target slowly and parallel to the ground. 3) Signal sound becomes stronger and changes in pitch while getting closer to the target center and the circles start disappearing in the pinpoint graphics. -
Page 21: Rocks And Searching In Rocky Terrains
bars will rise according to the intensity. This measurement can be summarized as the level of magnetic property and intensity of the ground. This measurement is important from two aspects. First, on grounds with high magnetic mineralization, search depth is low and users should be aware of this fact. Second, magnetic mineralization is a property which is particularly seen with mineralized rocks and this measurement plays an important role for the device to eliminate the false signals produced by these rocks. -
Page 22: Detection On The Beach And Underwater
DETECTION ON THE BEACH AND UNDERWATER SIMPLEX+ is a waterproof metal detector. This provides convenient detection underwater and on the beach. As explained before, salt water and alkali grounds are significantly conductive and cause effects similar to iron in detectors. SIMPLEX+'s Beach mode is specially designed for such conditions. You can perform your search easily using the Beach mode without requiring any special settings. -
Page 23: Technical Specifications
1.3 kg (2.9lbs.) including the search coil Length 63cm - 132cm (25" - 52") adjustable Battery 2300mAh Lithium Polymer Warranty 2 years Nokta Makro Detectors reserves the right to change the design, specifications or accessories without notice and without any obligation or liability whatsoever. KKSP55000389EN...