Download Print this page

Waterworks On Tap OTKM10 Installation Manuallines

One hole high profile kitchen faucet

Advertisement

Quick Links

INSTALLATION GUIDELINES
IMPORTANT:
To ensure this product is installed properly, you must read and
follow these guidelines.
The owner/user of this product must keep this information for
future reference.
This product must be installed by a professional licensed
contractor.
Be sure your installation conforms to federal, state, and local
codes. In the State of Massachusetts, all installations must comply
with the rules and regulations set forth within 248 CMR.
Inspect this product to ensure you have all the parts required for
proper installation. Product is sold partially assembled but shown
fully disassembled for illustrative and service purposes only.
Use only a strap wrench or protected/smooth-jaw wrench on any
finished surface.
The use of certain plumber's putty may stain stone or tile surfaces.
If further assistance is required, please contact Product Support at
1-800-927-2120 Monday through Friday, 8am – 6pm EST.
Refer to the separate Service Parts Documents for available
replacement parts.
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
TECHNICAL DETAILS:
DETAIL
ADJUSTABLE VERSUS FIXED SPRAY
MAXIMUM DECK THICKNESS
FITTINGS HOLE DIAMETER
HANDLE TURN ANGLE
INLET CONNECTION
RESTRICTED MAXIMUM FLOW RATE
SPOUT REACH
SPOUT SWIVEL
SPRAY HOSE LENGTH
SPRAY INCLUDED IN UNIT
WATER PRESSURE RANGE
WATER PRESSURE RECOMMENDED
UK Style No. OT10KM is supplied with 2 BSPP adapters, assembly required.
†† SPRAY can be installed on RIGHT or LEFT side of FAUCET
3-1/8"
[79mm]
MINIMUM
[51mm]
FROM CENTER TO
FAUCET
FINISHED WALL/
FITTINGS
BACKSPLASH
HOLE
[MOUNTING SURFACE – TOP VIEW]
STYLE No. OTKM10, OT10KM
On Tap One Hole High Profile Kitchen Faucet
with Metal Wheel, Black Ball Handle and Spray
SPECIFICATION
1-15/16" [49mm]
2" [51mm] - (FAUCET)
1-1/2" [38mm] - (SPRAYER)
QUARTER TURN
3/8" COMPRESSION CONNECTOR HOSES
2.2gpm [8.3L/min]
10-1/8" [257mm]
20psi [1.5 bar] MIN
85psi [6.0 bar] MAX
45psi [3.0 bar]
Ø2"
Ø1-1/2"
[38mm]
SPRAY
FITTINGS
HOLE
PAGE 1 OF 5 | UPDATED ON 8.1.2018
FIXED
YES
49" [1.2m]
YES
BACKSPLASH/
FINISHED WALL

Advertisement

loading

Summary of Contents for Waterworks On Tap OTKM10

  • Page 1 [79mm] BACKSPLASH/ Ø2" Ø1-1/2" MINIMUM FINISHED WALL [51mm] FROM CENTER TO [38mm] FAUCET FINISHED WALL/ SPRAY FITTINGS BACKSPLASH FITTINGS HOLE HOLE [MOUNTING SURFACE – TOP VIEW] PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 1 OF 5 | UPDATED ON 8.1.2018...
  • Page 2 RUBBER WASHER and NUT RED for hot. over the HOSES and TUBES. Ensure the SPOUT is properly aligned then thread and securely tighten the NUT. PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 2 OF 5 | UPDATED ON 8.1.2018...
  • Page 3 NUT. HOSE (hex end) onto the ADAPTER on the OUTLET TUBE. NOTE: A FLOW REGULATING CHECK VALVE is located inside the ADAPTER. PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 3 OF 5 | UPDATED ON 8.1.2018...
  • Page 4 SCREWS and STEM ADAPTER from the BRACKET. Remove Remove the ADAPTER and CARTRIDGE. the HANDLE. NOTE: Do NOT discard the STEM ADAPTER. NOTE: Do NOT discard the STEM ADAPTER. PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 4 OF 5 | UPDATED ON 8.1.2018...
  • Page 5 Loosen, but do NOT remove, the SET SCREW at the base of the SPOUT then pull the SPOUT off to expose the POST with external O-RINGS. NOTE: A DIVERTER is located inside the POST. PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 5 OF 5 | UPDATED ON 8.1.2018...

This manual is also suitable for:

On tap ot10km