Download Print this page
Waterworks Henry HNKM70 Installation Manuallines

Waterworks Henry HNKM70 Installation Manuallines

One hole gooseneck kitchen faucet with pull-down spray and metal lever handle

Advertisement

Quick Links

INSTALLATION GUIDELINES
IMPORTANT:
To ensure this product is installed properly, you must read and
follow these guidelines.
The owner/user of this product must keep this information for
future reference.
This product must be installed by a professional licensed
contractor.
Be sure your installation conforms to federal state, and local
codes. In the State of Massachusetts, all installations must comply
with the rules and regulations set forth within 248 CMR.
Inspect this product to ensure you have all the parts required for
proper installation. Product is sold partially assembled but shown
fully disassembled for illustrative and service purposed only.
Use only a strap wrench or protected/smooth-jaw wrench on any
finished surface.
The use of certain plumber's putty may stain stone or tile surfaces.
If further assistance is required, please contact Product Support at
1-800-927-2120 Monday through Friday, 8am – 6pm EST.
Refer to the separate Service Parts Documents for available
replacement parts.
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
TECHNICAL DETAILS:
DETAIL
ADJUSTABLE VERSUS FIXED SPRAY
HANDLE TURN ANGLE
INLET CONNECTION
RESTRICTED MAXIMUM FLOW RATE
SPOUT REACH
SPOUT SWIVEL
SPRAY HOSE LENGTH
SPRAY INCLUDED IN UNIT
WATER PRESSURE RANGE
WATER PRESSURE RECOMMENDED
UK Style No., HN70KM is supplied with 2 BSPP adapters, assembly required.
MOUNTING
SURFACE
STYLE No. HNKM70, HN70KM
Henry One Hole Gooseneck Kitchen Faucet
with Pull-Down Spray and Metal Lever Handle
SPECIFICATION
ADJUSTABLE
QUARTER TURN
3/8" COMPRESSION CONNECTOR HOSES †
2.2gpm [8.3L/min]
7-9/16" [193mm]
YES
49" [1.2m]
YES
20psi [1.5 bar] MIN
85psi [6.0 bar] MAX
45psi [3.0 bar]
Ø 1-3/8"
[35mm]
FITTINGS
1/4" MIN
[6mm]
3-1/4" MAX
[83mm]
DECK
THICKNESS
PAGE 1 OF 6 | UPDATED ON 5.9.2018
HOLE

Advertisement

loading
Need help?

Need help?

Do you have a question about the Henry HNKM70 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Waterworks Henry HNKM70

  • Page 1 Refer to the separate Service Parts Documents for available replacement parts. MOUNTING SURFACE Ø 1-3/8" [35mm] FITTINGS HOLE 1/4" MIN [6mm] 3-1/4" MAX [83mm] DECK THICKNESS PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 1 OF 6 | UPDATED ON 5.9.2018...
  • Page 2 CONNECTOR HOSES and the SUPPLY TUBES are marked WASHER beneath the ESCUTCHEON. BLUE for cold and RED for hot. NOTE: The HANDLE can ONLY be installed on the RIGHT SIDE. PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 2 OF 6 | UPDATED ON 5.9.2018...
  • Page 3 WEIGHT over the SLEEVE then securely tighten the SCREW to secure the WEIGHT in the desired position. NOTE: Ensure the METAL WASHER fits properly around the HOSES. PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 3 OF 6 | UPDATED ON 5.9.2018...
  • Page 4 BLUE for cold and RED for hot. inside the ADAPTER as well as an additional CHECK CAUTION: Flush out the supply lines prior to installing the VALVE. SPRAYER. PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 4 OF 6 | UPDATED ON 5.9.2018...
  • Page 5 SPRAYER then slide the COLLAR and O-RING SPRAYER using the RUBBER WASHER provided. SPRAYER making sure to include the O-RING. over the SPRAY HOSE. PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 5 OF 6 | UPDATED ON 5.9.2018...
  • Page 6 Adjust the position of the WEIGHT if necessary. 2.5mm HEX KEY. NOTE: Do NOT loosen or remove the SET SCREW at the base of the SPOUT. PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 6 OF 6 | UPDATED ON 5.9.2018...

This manual is also suitable for:

Henry hn70km