Cisco BEKEM Manual

Cisco BEKEM Manual

Ip phone key expansion module

Advertisement

Advertisement

Table of Contents
loading

Summary of Contents for Cisco BEKEM

  • Page 1: Table Of Contents

    • Connect a Key Expansion Module to a Cisco IP Phone, on page 4 • Connect Two or Three Key Expansion Modules to a Cisco IP Phone, on page 8 • Auto Detection of Key Expansion Modules, on page 11 •...
  • Page 2 Cisco IP Phone 8800 Key Expansion Module with a Cisco IP Phone 8851/8861 Key Expansion Module or with a Cisco IP Phone 8865 Key Expansion Module. You cannot mix audio expansion modules with video expansion modules. You also cannot use a video expansion module on an audio phone or an audio expansion module on a video phone.
  • Page 3: Key Expansion Module Power Information

    Cisco IP Phone Key Expansion Module Key Expansion Module Power Information Table 2: Cisco IP Phones and Supported Cisco IP Phone 8851/8861 Key Expansion Module and Cisco IP Phone 8865 Key Expansion Module Cisco IP Phone Model Supported Numbers of Key Expansion Modules and Buttons Cisco IP Phone 8851 2;...
  • Page 4: Connect A Key Expansion Module To A Cisco Ip Phone

    Cisco IP Phone 8861, unless Cisco Universal PoE (UPoE) is used. • Cisco IP Phone 8851 with 2 key expansion modules works on 802.3at PoE only with v08 or later hardware. You can find the phone version information on the lower back of the phone as part of the TAN and PID label.
  • Page 5 Cisco IP Phone Key Expansion Module Connect a Key Expansion Module to a Cisco IP Phone Procedure Step 1 Unplug the Ethernet cable from the phone. Step 2 If installed, remove the footstand from the phone. Step 3 Locate the accessory connector covers on the side of the phone.
  • Page 6 Position the phone so that the front of the phone faces up. Step 6 Connect one end of the key expansion module spine connector to the accessory connector on the Cisco IP Phone. a) Align the spine connector with the accessory connector ports.
  • Page 7 Cisco IP Phone Key Expansion Module Connect a Key Expansion Module to a Cisco IP Phone Step 8 (Optional) Use a second key expansion module spine connector to connect the second key expansion module to the first key expansion module.
  • Page 8: Connect Two Or Three Key Expansion Modules To A Cisco Ip Phone

    Cisco IP Phone Key Expansion Module Connect Two or Three Key Expansion Modules to a Cisco IP Phone Note Make sure that the screws are fully inserted into the phone and tightened. Step 11 (Optional) Install the footstands on the phone and on the key expansion module, and adjust both footstands to rest evenly on the work surface.
  • Page 9 Position the phone so that the front of the phone faces up. Step 6 Connect one end of the key expansion module spine connector to the accessory connector on the Cisco IP Phone. a) Align the spine connector with the accessory connector ports.
  • Page 10 Step 9 Use a third key expansion module spine connector to connect the third key expansion module to the second (middle) key expansion module. This figure shows a Cisco IP Phone with three key expansion modules attached. Cisco IP Phone Key Expansion Module...
  • Page 11: Auto Detection Of Key Expansion Modules

    When a user adds key expansion modules to these phones, the module lights up and is enabled automatically. Default value of this field is 2 for Cisco IP Phone 8851 and 3 for Cisco IP Phone 8861.
  • Page 12: Configure The Key Expansion Module From The Phone Web Page

    Cisco IP Phone Key Expansion Module Configure the Key Expansion Module from the Phone Web Page If your user has an older release phone and it is upgraded to the current release, you can change the cofiguration of the phone so that when the user adds a key expansion module to the phone, it lights up and is enabled automatically.
  • Page 13: Allocate A Key Expansion Module Type

    Press Save. Reset the Single LCD Screen Key Expansion Module If you are having technical difficulties with your Cisco IP Phone 8800 Key Expansion Module, you can reset the module to the factory default settings. Cisco IP Phone Key Expansion Module...
  • Page 14: Troubleshoot The Key Expansion Module

    Cisco IP Phone Key Expansion Module Troubleshoot the Key Expansion Module Procedure Step 1 Restart the key expansion module by disconnecting the power source, waiting a few seconds, and then reconnecting it. Step 2 As the key expansion module powers up, press and hold Page 1. As the LCD screen turns white, continue pressing Page 1 for at least one second.
  • Page 15 Cisco IP Phone Key Expansion Module Key Expansion Module Does Not Go Through the Normal Start Up Process • Power over Ethernet (PoE) doesn't meet the required power-supply. • Connected number of key expansion modules exceed maximum "Number of Units".
  • Page 16 Cisco IP Phone Key Expansion Module Key Expansion Module Does Not Go Through the Normal Start Up Process Cisco IP Phone Key Expansion Module...

This manual is also suitable for:

Cp-8800-audioCp-8800-video

Table of Contents