Table of Contents
Advertisement
Quick Links
1. Illustration to buttons
VOL+
SET
OPEN
CLOSE
"
MIN
"
Radio channel up / Minute
HOUR
"
"
radio channel down/ Hour
VOL+
"
SET
"
volume up/ time setting shift
"
OPEN
"
volume down/ open memory channel
MEM
"
"
radio channel memory/ lock channel
CLOSE
"
"
select radio channel / close channel
OZONE
"
"
ozonizer on/off
HEAT
"
"
preheat on/ off or preset
Note：
1.
All the functions listed on the key in blue letter only works on the "off" model.
PUMP2
2.
function is not available on SPA-329,312, which model without water column and waterfall.
PROGRAMMING INSTRUCTIONS
TEMP
OZONE
LOCKED
AM
PM
MIN
LIGHT
BLOWER
HOUR
MEM
CD
Fig﹒1：Sketch map of big massage bathtub
F
SET
HEAT
ON
OFF
PUMP1
PUMP2
PUMP3
PUMP3
ON/OFF
ON/OFF
" power
"
RADIO
CD
"
"
radio on/ off or CD shift
"
F/
C
"
blower on/ off or ℃ & ℉ Shift
"
"
LED & fiber optic lights on/ off
"
"
whirlpool pump 1&2 on/ off
PUMP2
"
"
waterfall & column pump on/ off
PUMP3
"
"
whirlpool pump 3 & circulation pump
on/ off.
TEMP
"
"
OZONE
F/
C
PUMP2
HEAT
On/ Off or mode shift
1
Advertisement
Table of Contents
Related Manuals for JNJ SPAS SPA-329
Summary of Contents for JNJ SPAS SPA-329
- Page 1 “ ” Temperature setting Note： All the functions listed on the key in blue letter only works on the “off” model. PUMP2 function is not available on SPA-329,312, which model without water column and waterfall.
- Page 2 2. Functions Summary (1) Constant heating, preheating, displaying and setting water temperature. (2) Display time in AM & PM 12 hours mode. (3) Circulation cleaning and presetting circulation cleaning. (4) Radio, 10 channels memory or circumscribe device of CD or DVD, offering power output for DVD/CD and TV set.
- Page 3 HOUR ” ” On the “ off” status and the preheat and circulation cleaning without working, press “ or “ key to start time setting.。The “：” signal will stop to flash, but the minute and hour will flash at this time。 HOUR To press the “...
- Page 4 HOUR To press the “ ”key one time，will add one hour, the hour number will be displaying on the screen. HOUR Pressing the“ ” without stop, the hours will increase continually till stop pressing the key. The hours adjustment range is AM 0~PM 11 . To press the “...
- Page 5 PUMP3 (5） Press “ ”to confirm *** Notice *** (1)、the setting steps of Circulation-cleaning must be operated on the “ off” status. (2)、During the whole setting process, the circulation pump and ozonizer are not working. Preheating setting： 、 Only one preheating setting program can be set in one day in a spa. The preheating woking status will be displaying on the LCD screen.
- Page 6 adjustment range is AM 0~PM 11 . To press the “ ”key one time，will add one minute, the minute number will be displaying on the screen. Pressing the“ ”without stop, the minutes will increase continually till stop pressing the key. The minutes adjustment range is 0-59 .
- Page 7 *** Notice *** 1、 all the setting steps of preheating must be operated on the “off” status, and the LCD displays “---”. 2、 Please note that if the screen shows "on" or "off". If the screen showing "on" signal, indicates preheating function is on. , when the time reach to the set time of preheating, the heater will work automatically.
- Page 8 3, If the above conditions are delivered, and the heater is still not working, please draw the wire of water pressure sensor from the heater, then connect two ends of this wire directly, and the heater will works normally. 8、 Turn ON/ OFF operation. On the “off”...
- Page 9 CLOSE “ ” continually will take out the memorized radio frequency from channels will be saved at present channel by pressing this key continually。If none of the channel， LCD will display “---” 。 Ⅴ） 、Press the key “ ” could memorize the present radio channel， Pressing the key “...
- Page 10 ” “ 1)To press the key to turn on/off blower. The blower can work without any water in tub. So it’s way to test if the spa system connect with power successfully or the controller is working or not? 2) Blower will be shut down automatically after it has been working for 2 hours. 16、Fahrenheit &...
- Page 11 The installation instruction shall state the substance of the following: - Earthed appliances must be permanently connected to fixed wiring; - The appliance should be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 mA. - The floor has to be capable of supporting the expected load.