Advertisement
UNIT SELECTION
1. Once the Peak / Track mode has been set, the wrench switches to the setting of
"UNIT SELECTION".
2.
is shown on screen, select the units between lb/ft, lb/in, kg.m, N.m by
Ft/lb
pressing
button.
3. Press
button to confi rm the unit selection. The wrench will switch to Auto Power Off
Settings when the button is pressed.
NOTE: If there is no button activity for 3 seconds, the wrench will retain the last selection of Units,
and return to measurement mode.
AUTO POWER-OFF SETTINGS
The torque wrench will be turned off automatically without any button activity over a selectable
period. Changing the auto –off setting as follows:
1. Once the unit is selected, the default Auto-Off time: 5 (5 minutes) will be shown on screen.
2. Wait for 2 seconds without touching any buttons, or press
setting.
3. Changing the wrench Auto-off time by pressing
between 5 minutes, 15 minutes or "OFF" to turn off the Auto-off function.
4. Press
button to confi rm the selection. The wrench returns to measurement mode when
the button is pressed.
NOTE: If there is no button activity for 3 seconds, the wrench will retain the last selection of Auto
Power Off, and return to measurement mode.
PROGRAMMING THE TORQUE AND ANGLE
The wrench has 5 sets of memory storage for pre-setting the target Torque and Angle.
TARGET TORQUE SETTING
1. Press
button to turn the wrench on.
2. Press
button to select the memory storage number between M1~M5.
3. Once the memory number is chosen, access the target Torque/ Angle programming
by pressing and holding
button for 5~10 seconds.
4. Release
button when
SET
played. The fi rst digit of this value ("0000" ) is fl ashing. Press
saved value. Or by repeatedly pressing
increased. When the desired value is reached, press
place. Repeat this process for all numeric places. (ones, tens, hundreds etc.) Example: A cor-
rect setting for 75 lb/ft will read 075.0 in the display.
5. When the required torque level is set, press
4
Eastwood Technical Assistance: 800.544.5118 >> techelp@eastwood.com
button to retain the default
button. Select the shut-off time
is shown on screen, and the last saved torque is dis-
button to zero the last
button, the value of the fl ashing digit is gradually
button to skip to the next decimal
to save the value.
NOTE: If there is no button activity for 5 seconds, the wrench will retain the last selection of torque
and automatically switch back to Angle Programming.
NOTE: "Erro" (for ERROR will show on the display when the pre-set torque value exceeds 100% of the
maximum torque value. After 1 second, the display returns to torque Measurement Mode.
NOTE: After pressing the "+" button to access the torque setting mode, without any activity after
6 seconds, the display will return to Measurement Mode.
TARGET ANGLE SETTING
1. The display skips to Angle setting automatically once the target torque is set, and displays the
last saved angle value. The fi rst digit of this value ("0000") is fl ashing.
2. Press the
button to zero the last saved value. Or by repeatedly pressing
the value of the fl ashing angle digit is gradually increased. When the desired value for this digit
was achieved, press
button to skip to the next digit. Repeat this process for all numeric
places in the angle value.
3. When the required angle is set, press
NOTE: If there is no button activity for 5 seconds, the wrench will retain the last selection of
Angle Setting and automatically switch to Measurement Mode.
TURNING THE DISPLAY ILLUMINATION ON / OFF
1. The display illumination can be turned on prior to or after programming the torque.
2. In order to do this, press and release the
OPERATING THE TORQUE WRENCH
1. Select the socket required for your work.
2. Attach the socket fi rmly to the square drive of the torque wrench, it will be held in place by the
ball stop of the square drive.
3. If possible, do not use any extensions because they may distort the torque applied to a bolt.
APPLYING PROGRAMMED TORQUE
1. Program the value necessary following the instructions in the Target Torque Setting section.
2. Place the torque wrench on the fastener. Grip the torque wrench and PULL on the wrench with
a slow, easy movement. Avoid jerky movements.
3. With the target torque pre-set, the target value is indicated on the screen.
4. The LED will show GREEN when you are under 50% of the programmed torque value.
5. When approaching the target torque value,, the LED turns to YELLOW.
6. When you approach the programmed torque value, the buzzer will sound.
7. When you are within 2% of the programmed torque value, the RED LED will illuminate.
Once the torque is reached, the buzzer will emit quicker sound sequence.
8. If you exceed the programmed torque by 2%, the buzzer will emit a continuous tone and the
LED will turn GREEN.
ATTENTION: When you hear the continuous tone and the RED LED illuminates, stop pulling
immediately or target torque will be exceeded.
To order parts and supplies: 800.345.1178 >> eastwood.com
button,
to save the value.
button.
5
Advertisement
