Table of Contents
Advertisement
Quick Links
Echoflex Installation Guide
Elaho Preset Station
Overview
Elaho Preset Stations activate built-in
presets in compatible power control
products.
Station faceplates and buttons are
available in cream, ivory, gray, black
and signal white. Preset stations are
provided with station electronics,
buttons, faceplate, a termination kit,
and installation hardware.
This document guides you through
the installation and local configuration of the Preset Station. Advanced
(custom) functionality is available using ElahoAccess.
Custom Configuration
For information about the custom configuration options available for the
Preset Station using ElahoAccess, reference the ElahoAccess Mobile App
integrated help system. User documentation is available for download on our
website
Note:
switch 2 must be enabled. Reference
next page
Main Offic e
Squamish, BC, Canada
n
Email
info@echoflexsolutions.com
© 2018 Echoflex Solutions, Inc.
8140M2110
Revision A
Released 2018-09
n
n
echoflexsolutions.com
To use the configuration settings applied using ElahoAccess, DIP
.
Toll Free +888 324 6359
n
W eb
echoflexsolutions.com
n
Echoflex intends this document to be provided in its entirety.
n
.
Rotary and DIP Switches on the
Phone +778 733 0111
n
n
Product information and specifications subject to change.
n
Fax +604 815 0078
Advertisement
Table of Contents
Related Manuals for ETC echoflex Elaho Preset Station
Summary of Contents for ETC echoflex Elaho Preset Station
- Page 1 Echoflex Installation Guide Elaho Preset Station Overview Elaho Preset Stations activate built-in presets in compatible power control products. Station faceplates and buttons are available in cream, ivory, gray, black and signal white. Preset stations are provided with station electronics, buttons, faceplate, a termination kit, and installation hardware.
-
Page 2: Prepare For Installation
Echoflex Installation Guide Preset Station Prepare for Installation Preset Stations ship with a termination kit for use with Belden 8471 (or equivalent wire) and contains a power pigtail, a ground wire pigtail, receptacle spacers, and all required wire termination connectors for installation. -
Page 3: Preset Station
Echoflex Installation Guide Preset Station Set the Address rotary switch to the desired address (1 through 16) for the station identification in the assigned Space. CAUTION: Each device on the bus must have its address set to a unique number (1 through 16) for the space it controls. If two or more devices use the same address for the same space, the system will not function properly. -
Page 4: Installation
Echoflex Installation Guide Preset Station Installation Installation should follow all local codes and standard electrical practices. The back box should be installed level and square for best results. Ensure that the back box is clean and free of obstructions. Note: NEC Class 2 product to be wired in accordance to NEC Article 725 and local jurisdiction requirements. -
Page 5: Installing The Station In The Back Box
Echoflex Installation Guide Preset Station Terminate EchoConnect wires. EchoConnect is topology free, you may install the wires in any combination of bus, star, loop, or home-run. Strip 7/16” (11 mm) from the ends of each power pigtail wire provided in the termination kit and the installed control wires. Use the WAGO connectors provided to connect the power pigtail wires and the installed Belden 8471 control wires. -
Page 6: Installing The Faceplate
Echoflex Installation Guide Preset Station Installing the Faceplate The faceplate is secured to the station with two magnets that are located on the bottom edge of the faceplate. Align the top of the faceplate approximately 20 degrees to the station. Hook the top of the faceplate on the tabs located on the top of the station electronics assembly. -
Page 7: Assigning Presets
Echoflex Installation Guide Preset Station Settings Settings for Basic config mode (DIP switch 2 set to Off) can be modified locally including changing which presets are assigned to the station, changing the button LED color, and preset recording at the station. Assigning Presets Stations default to controlling Presets 1 through 5. - Page 8 Echoflex Installation Guide Preset Station Changing Button LED Color Stations default to illuminating preset buttons in green. To change the color of the LEDs at the station follow this procedure: Press and hold the [MODE] button for five seconds. The LED beneath the [MODE] button will illuminate and all of the preset buttons will display in their current configured color.