Changing the oil ..........................29 Changing the oil of the multiplier gear .................... 30 Conveyor maintenance ........................30 4.10 Lubrication ............................32 4.11 pressure regulating valves ....................... 36 4.12 Washing and cleaning ........................37 4.13 Storage ............................. 37 HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Page 3
Jamming of the cutting blade ......................39 Jamming of the wood on the splitting knife ..................39 Hydraulics diagram (tractor-operated machine)..................40 Guarantee terms and declaration of conformity ..................41 EC Declaration of Conformity for the machine ....................42 HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
1.2 PURPOSE OF USE The Hakki Pilke Raven firewood processor is designed for the preparation of firewood from pruned wood or logs. The firewood processor must not be used to process any treated wood, such as is found in construc- tion waste, for example.
When cleaning the machine or carrying out any maintenance, it must be disconnected from its power source. Note! Do not leave a running machine unsupervised! 1.6 NOISE AND VIBRATION The vibration values do not exceed 2.5 m/s2. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Page 6
EWARE OF MOVING PARTS EWARE OF THE CHAIN EWARE OF THE CARDAN SHAFT NLY ONE PERSON MAY OPERATE EWARE OF THE KNIFE ISCONNECT THE POWER SUP- THE MACHINE PLY BEFORE CARRYING OUT MAINTENANCE PROCEDURES HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Page 7
HE MAXIMUM SPEED FOR THE THE DIRECTION OF THE ARROW CARDAN SHAFT IS HE MAXIMUM PERMITTED ANGLE OF THE CONVEYOR IS 40°. D O NOT PASS UNDER THE AW CHAIN OIL YDRAULIC OIL CONVEYOR ANGER ZONE UBRICATION POINT HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
In the event of any defects or damage, contact the retailer immediately. 2.2 MAIN COMPONENTS OF THE MACHINE The main components of the Hakki Pilke Raven firewood processor are presented in the figure below. A. Input conveyor B.
Section 1.5. Note! Inspect and clean the machine before setting it up for transport! Placing the output conveyor in the operating or transport position Figure 2. Figure 3. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Page 10
When placing the input conveyor in the transport position, lift the conveyor to the upper position, turn locking latch B into its slot and insert pin A (Figure 3). Use holder C to lock the support leg in place (Figure 2). HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Page 11
4. Turn the upper section of the conveyor into the operating position using handle B (Figure 6). Figure 6. 5. Turn support bar C on the output con- veyor belt (Figure 7) to the side. Figure 7. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Page 12
5. Lift the conveyor with the winch until it locks into the raised position. Ensure that lock A (Figure 5) settles properly into place. Note! Do not stand on the output conveyor! Do not use the winch if the belt is worn! HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Finally, ensure that all connections are safe and secure. Never use a damaged or unprotected cardan shaft. Note! Tractor-powered machines must be attached to the lifting equipment of the tractor. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Page 14
Figure 11. Starter. Note! Only connect the machine to a fault current protected socket. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
The machine must be placed in the transport position whenever it is moved. Exercise extreme caution when moving the machine in the operating position. Always lower the machine to the ground when you stop. Note! Incorrect lifting may cause a hazardous situation or damage the machine. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
The control valve makes sure that the end of the log meets the measuring device at the desired point of the splitting cycle. Figure 13 HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
The swivel out-feed conveyor can be locked to the desired position using the lever F. In-feed conveyor lever. The in-feed conveyor belt rotates forward by moving lever F in Figure 15 to the right. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Open the guard and see if the saw chain has been supplied with oil. 8. Ensure that the saw chain starts running when you lower the saw bar by about 2 cm using lever C (Figure 15). HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Note! Only move the splitting beam forward for the required length. For example, if you have ad- justed the machine for logs of 35 cm in length, the splitting beam needs to move only approx. 37 cm. This notably increases the efficiency of the machine. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
3.4 USING THE OUTPUT CONVEYOR The Hakki Pilke Raven firewood processor’s output conveyor belt is driven by a hydraulic motor. The output conveyor can be adjusted laterally and vertically. The following describes how the conveyor can...
Page 21
If the conveyor is jammed for any reason, the machine must be shut down before removing the cause. There must be at least 50 cm between the end of the output conveyor and the pile of pro- cessed firewood. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Turn off the machine and disconnect the power cable from the socket. Ensuring that the machine is inactive Once you have disconnected the machine from its power source, always ensure that the machine is com- pletely inactive before performing any other measures! HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
4.2 ADJUSTING THE LOG LENGTH The Hakki Pilke Raven firewood processor is equipped with a mechanical log measuring device with an in- cremented adjustment value of 25 to 50 cm. 1. Turn off the machine, disconnect it from any power source, and open the protective cover of the machine.
The knife can be driven to the lowest position in one go by raising the knife and clearing the space under the knife of firewood. The machine must be shut down and disconnected from its power source for the duration of the cleaning. Figure 21. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
2. Turn off the machine and disconnect it from its power source. 3. Open the guard and lift the splitting knife out of its slot. Install a new splitting knife by reversing the above steps. Figure 22. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
The tightness and alignment of the output conveyor belt can be adjusted using nuts A (2 pcs) in Figure 23. Loosen adjustment nuts A on the side you wish the belt to run. Figure 23. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
To check the tension of the saw chain, wear protective gloves and pull the lower edge of the chain. The tension is correct if you can pull out three to four teeth of the chain into full view by applying moderate force. Note! Use protective gloves when handling the saw! Figure 24. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Page 28
4. Place the new bar against gear wheel B (Figure 27), twist it into the groove and loosely attach the saw bar bolts and fastening plate A. 5. Attach and tighten the saw chain according to steps 6-8 in Section 4.6 “Replacing and tightening the saw chain”. Figure 27. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
5. Tighten plug B firmly, and fill the tank with fresh oil (approx. 40 litres). Figure 28. 6. Finally, ensure that the oil level set- tles at the halfway point of gauge D (Figure 30). Figure 29. Figure 30. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
(See Section 2.3). 3. Move the belt joint to a suitable height. 4. Disconnect the joint by using pliers, for example, to pull out pin A (Figure 31) Figure 31. that holds the joint together. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Page 31
5 cm when the conveyor is in the operating position. An excessively tight belt may be damaged more easily, and it places unnecessary strain on the conveyor bearings. Figure 34. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
3. Grease nipple of the wood limiter in Figure 40. 4. Guard nipples (2 pcs) in Figures 41 and 42. 5. Nipples (2 pcs) of the output conveyor's drive roller in Figure 43. 6. Nipples in Figures 44-47. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
SPO25-VM-B17-B Spare part num- ber: 97290 Cutting blade Sharpen as neces- 0.325” 66/1.5 sary Spare part num- bers: Chain: 95148 Bar: 95145 Machine Clean Wash Electric motor Clean Electrical equip- Clean/check visu- ment ally HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
The machine makes an ab- normal noise. The electric motor does not The machine makes a loud The fuse has blown. Replace start. noise, but does not start. The input cable is faulty. Replace the cable. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
The new piece will then push the bottom part of the jammed piece past the knife. Lower the knife by approx. 5 cm and repeat step 3. Repeat step 4 until the jammed wood has passed the knife, piece by piece. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
10. A spare part will be delivered free of charge when using the usual means intended for such parts, in accordance with the normal schedule. 11. The receiver is liable for costs occurring from special deliveries, such as express mail. HAKKI PILKE RAVEN TRANSLATION VERSION 1-2015...
Name: Tapio Aittokoski Address: Valimotie 1, FI-85800 Haapajärvi, Finland The aforementioned person assures that Hakki Pilke Raven firewood processor Serial number: ………………………… is compliant with the applicable regulations of the Machinery Directive (2006/42/EC). Location and date: Haapajärvi 1 July 2015...