Advertisement
Quick Links
DRESSING TABLE
Assembly Instructions
CONTENTS:
1x Lid (with mirror)
A
1x Lid infill
B
1x Top panel (left)
C
1x Top panel (right)
D
1x Back panel
E
1x Inside back panel
F
1x Left outer side panel
G
1x Left inner side panel
H
1x Right inner side panel
I
1x Right outer side panel
J
4x Soft close drawer runners
K
(2x left, 2x right)
1x Base
L
1x Front panel
M
1x Decorative panel
N
4x Legs
O
2x Drawer backs
P
2x Drawer sides (left)
Q
2x Drawer sides (right)
R
2x Drawer base
S
1x Drawer fronts (left)
T
1x Drawer fronts (right)
U
4x Soft close clips (2x left, 2x right)
V
4x Leg mounting plates
W
RECOMMENDED:
• TOOLS:
Screwdriver & Hammer
• TWO PERSON BUILD
Page 1 of 6
8x
8x
One piece
Plastic
Euro Screws
connectors
dowels
34x
2x
Wood Screw
Wood Screw
Soft close hinge
(3.5x16mm)
(4x18mm)
1x
2x
Soft close hinge
Soft close
Hinge brackets
(right-grey)
hinge cover
36x
36x
Cams
Dowels
Wooden dowels
2x
1x
Wall mounting
Wood glue
Cable hole plug
brackets
We recommend you use the Wall Mounting
Brackets provided to fix the dressing table to
a wall (where possible). This will prevent the
unit being pulled over. Use suitable fixings.
www.spaceslide.co.uk/diy-installation-and-information
8x
1x
(left-white)
1x
pair
(left & right)
8x
2x
Call: 0800 9803499
V2
SS_INSTRUC_DT_05.2016
Advertisement
Related Manuals for spaceslide Dressing Table
Summary of Contents for spaceslide Dressing Table
- Page 1 RECOMMENDED: We recommend you use the Wall Mounting • TOOLS: Screwdriver & Hammer Brackets provided to fix the dressing table to • TWO PERSON BUILD a wall (where possible). This will prevent the unit being pulled over. Use suitable fixings.
- Page 2 Fit the Cams (10) on the sides of the panel and the dowels Push/tap sides (H&I) onto panel (F). (11) in the centre. Lay panel (L) on a flat surface. (Ensure the Cams are facing inwards). Page 2 of 6 SS_INSTRUC_DT_05.2016 www.spaceslide.co.uk/diy-installation-and-information Call: 0800 9803499...
- Page 3 1 –tap dowels into panel (M). 2 – insert panel (N) on top. INSIDE DRAWER RUNNERS OUTSIDE DRAWER RUNNERS Screw through holes shown on both sides, at both ends of the unit. Page 3 of 6 SS_INSTRUC_DT_05.2016 www.spaceslide.co.uk/diy-installation-and-information Call: 0800 9803499...
- Page 4 (Shown from underneath). (Shown from back). Fit leg mounting plates to all 4 corners. Insert legs into holes and turn until tight. (Shown from underneath). Page 4 of 6 SS_INSTRUC_DT_05.2016 www.spaceslide.co.uk/diy-installation-and-information Call: 0800 9803499...
- Page 5 THEN INSERT Drawer back Tap plastic dowels gently into place with a hammer. Push/tap sides (R&Q) onto back panel (P). (Repeat on both drawers). (Repeat on both drawers). (Repeat on both drawers). Page 5 of 6 SS_INSTRUC_DT_05.2016 www.spaceslide.co.uk/diy-installation-and-information Call: 0800 9803499...
- Page 6 This will prevent the unit being pulled over. Use suitable fixings. Fix the Wall Mounting Bracket to the bottom of the Dressing Table. (Use suitable fixings when attaching to the wall). Page 6 of 6 SS_INSTRUC_DT_05.2016 www.spaceslide.co.uk/diy-installation-and-information Call: 0800 9803499...
- Page 7 DRESSING TABLE POWER CUBE Assembly Instructions Remove cable covers. 242mm Feed plug through and fix power cube. Position no more than 242mm from the front. Page 1 of 1 SS_INSTRUC_DTP_08.2015 www.spaceslide.co.uk/installation-and-technical-information Call: 0800 9803499...
Need help?
Do you have a question about the Dressing Table and is the answer not in the manual?
Questions and answers