Subscribe to Our Youtube Channel
Related Manuals for Thermann TH250GLE
Summary of Contents for Thermann TH250GLE
- Page 1 INSTALLER'S INSTALLER'S MANUAL MANUAL Electric Hot Water Tanks (Solar-Ready) Electric Hot Water Tanks (Solar-Ready) Installation Details Warranty Installation Details Warranty H0025 028627 A 1 1 1 H0025 028627 A 1 1 1...
- Page 2 Thermann Installer's Manual Electric Hot Water Tanks (Solar-Ready) Thermann Installer's Manual Electric Hot Water Tanks (Solar-Ready)
-
Page 3: Table Of Contents
CONTENTS Introduction CONTENTS Warnings and Precautions Site Inspection Introduction Component Inspection Warnings and Precautions System Plumbing Site Inspection Commissioning Component Inspection Auxiliary Heating System Plumbing Post Installation Commissioning Appendix Auxiliary Heating Warranty Post Installation Appendix Warranty 3 3 3 3 3 3... -
Page 4: Introduction
• Boost: the process where a heating component INTRODUCTION (such as an electric element) is used to provide auxiliary heating. • Collector: the Thermann solar collector includes TERMINOLOGY the manifold with heat pipes and evacuated tubes inserted. • Boost: the process where a heating component (such as an electric element) is used to provide •... -
Page 5: Warnings And Precautions
WARNINGS AND PRECAUTIONS INSTALLER REQUIREMENTS WARNINGS AND PRECAUTIONS Thermann recommends the use of an ECV on every Installation of a system must be completed by a licensed plumber and in accordance with the requirements installation. listed below, as well as any relevant local standards and regulations. - Page 6 Thermann Installer's Manual Electric Hot Water Tanks (Solar-Ready) Thermann Installer's Manual Electric Hot Water Tanks (Solar-Ready) Legionella Control: Legionella bacteria can be found naturally in the environment and thrives in warm water and damp places. It can weaken the body’s immune system, which can increase the chances of developing Legionnaires’...
-
Page 7: Site Inspection
SITE INSPECTION STORAGE TANK LOCATION • Products should always be handled with care. SITE INSPECTION • The storage tanks are to be installed at ground or Damage incurred during the transportation is not floor levele and must stand vertically upright as the covered under product warranty. -
Page 8: Component Inspection
Electric Hot Water Tanks (Solar-Ready) COMPONENT INSPECTION Thermann Installer's Manual Electric Hot Water Tanks (Solar-Ready) COMPONENTS PROVIDED BY THERMANN Upon receiving the system prior to installation, check COMPONENT INSPECTION that the following components have been provided. Any concerns must be brought to the attention of Thermann immediately. -
Page 9: System Plumbing
Storage Tank Ports: system schematic in Figure 5 in Appendix (page 15). Thermann tanks are hot water storage tanks that Refer to the schematic to get an understanding of how SYSTEM LAYOUT... - Page 10 THE HOT WATER REACHES THE HOUSE. away from the solar flow port: All ports on an Thermann Australia storage tank are Solar Flow: • Circulation Pump of 20mm (3/4”) BSP. Teflon tape must be used to This port is used for the water line directed up to the seal any fitting.
-
Page 11: Commissioning
When solar DHW system is set up, the sensors must be coated with heat transfer paste and inserted through The Thermann controller requires three sensor leads be the cable gland into the appropriate sensor port and installed into the appropriate sensor ports in the solar tightened. -
Page 12: Auxiliary Heating
To ensure optimal operation and to maintain the Glass-lined Bottom element Once per week for 60°C for 32 integrity of the Thermann EHW tank, ensure that each Table 3 Minimum Heat Requirements electric boosted system minutes of the following processes is carried out prior to leaving POST INSTALLATION the site. -
Page 13: Appendix
APPENDIX - SYSTEM SCHEMATIC APPENDIX - SYSTEM SCHEMATIC Figure 4 Typical Electric boosted solar hot water system Figure 4 Typical Electric boosted solar hot water system 15 15 13 15 15 13... -
Page 14: Warranty
Australia, to make the Unit accessible for repair or will be charged full costs of repair work. Unit will only be met by Thermann Australia where the be charged 80% of replacement parts. The owner replacement. - Page 15 Warranty claims can be placed by completing the following steps: Contact Thermann Australia on 1300 277 428 and speak to our Warranty and Aftersales Department. • Provide the serial number and model number of the Warranty claims can be placed by completing the following steps: HWS located on the white compliance sticker.
- Page 16 Thermann Installer's Manual Electric Hot Water Tanks (Solar-Ready) Thermann Installer's Manual Electric Hot Water Tanks (Solar-Ready) H0025 028627 A H0025 028627 A...
Need help?
Do you have a question about the TH250GLE and is the answer not in the manual?
Questions and answers
where is filter