Thermann 16NG50-6 Operating Instructions Manual
Gas continuous flow water heaters
Hide thumbs
Also See for 16NG50-6:
- Instruction manual (25 pages) ,
- Service manual (41 pages) ,
- Owner's manual (16 pages)
Subscribe to Our Youtube Channel
Related Manuals for Thermann 16NG50-6
Summary of Contents for Thermann 16NG50-6
-
Page 1: Operating Instructions
GAS CONTINUOUS FLOW WATER HEATERS OPERATING INSTRUCTIONS FOR MODELS 16NG50-6/16LP50-6, 16NG60-6/16LP60-6, 20NG50-6/20LP50-6, 20NG60-6/20LP60-6, 26NG50-6/26LP50-6, 26NG60-6/26LP60-6... - Page 2 OPERATING INSTRUCTIONS...
-
Page 3: Important Safety Instructions
Turn off the gas supply and power and Care on 1800 080 055. CLOSE No Fire Prohibited 5. If a power failure occurs the remote controls will not function and the Thermann unit will not supply hot water until power is restored. OPERATING INSTRUCTIONS... - Page 4 IMPORTANT SAFETY INSTRUCTIONS MEASURES TO BE TAKEN DURING ELECTRICAL STORMS the main power during electrical storms DO NOT INSTALL INDOORS Danger This unit is designed for outdoor installation. Never install SECURE SERVICE SPACE Make sure there is enough space around the unit for checking, service and maintenance.
- Page 5 IMPORTANT SAFETY INSTRUCTIONS DO NOT DISASSEMBLE, REPAIR OR MODIFY Warning relocation or connection to solar units. FLAMMABLE ITEMS Warning or use them around the unit. FREEZE PREVENTION This unit comes equipped with internal electric heaters that prevent the water inside the unit from freezing.
-
Page 6: Electrical Connection
IMPORTANT SAFETY INSTRUCTIONS MEASURES TO BE TAKEN IN CASE OF EMERGENCY The procedure to follow in an emergency such as Close Close 1. Close all hot water taps in the house. 2. Close the gas valve and the main water valve. 3. -
Page 7: Remote Control
REMOTE CONTROL complete control of your hot water. YST-2807 and ensuite. Digital Monitor Indicates the selected water temperature. Error messages flash in the event of failure. High Temp. Indicator Indicates the setting temperature is higher than 50 ゜ C. UP/DOWN Button In Use Indicator Increase or decrease the Indicates that a hot water... - Page 8 REMOTE CONTROL Operation of Controller 3. The priority indicator will illuminate. 5. Turn on the hot water tap or shower. The ``In Use´´ indicator will illuminate after a short delay. This indicator will remain illuminated until the hot water tap or shower is turned off.
- Page 9 REMOTE CONTROL Priority Control (Change) indication. Whilst hot water outlets are open, transfer of ``priority´´ to other remote controllers is Warning Do not turn off the remote controller or change the water temperature while someone is bathing or washing. That may result in scalds or burns. HINTS FOR USING REMOTE CONTROLS FOR SAFETY AND ENERGY SAVINGS prevent small children from scalding.
-
Page 10: Fault Monitor
FAULT MONITOR When installed with remote controllers the THERMANN HOT WATER UNIT HAS A SELF DIAGNOSING FUNCTION FOR FAULTS. When the unit does not operate correctly an error code is displayed on the remote the remote control display. DISPLAY PROBLEM... -
Page 11: Warranty
WARRANTY Warranty Conditions Failure is due to a fault in the manufacture of the product The installation of the product is in accordance with the instructions provided This warranty does not include faults caused by: Incorrect installation or installation not in accordance with the instructions provided Normal wear and tear Inadequate or complete lack of maintenance EXCLUSIONS... - Page 12 WARRANTY and AS/NZS3000, AS/NZS3500 and AS/NZS5601. Where a component may have failed under warranty and is replaced, the component warranty period. 6.5 to 8.5 Sodium Up to 150 mg/litre or ppm Up to 600 mg/litre or ppm Chlorides Up to 300 mg/litre or ppm Iron Up to 1 mg/litre or ppm Magnesium...
- Page 16 Works for you. ™...
Need help?
Do you have a question about the 16NG50-6 and is the answer not in the manual?
Questions and answers