Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Motorline professional MC50BR
Summary of Contents for Motorline professional MC50BR
- Page 1 MC50BR USER / INSTALLER MANUAL v. 164-br...
- Page 2 00. CONTENT INDEX 01. SAFETY INSTRUCTIONS 07. COMPONENTS TEST CAPACITOR SCHEME STANDARDS TO FOLLOW INPUTS TEST 02. THE CONTROL BOARD 08. TROUBLESHOOTING TECHNICAL SPECIFICATIONS INSTRUCTIONS FOR FINAL CONSUMERS/ TECHNICIANS PROGRAMMING PRE-RECOMENDATIONS 09. CONNECTION SCHEME 03. INSTALLATION CONNECTIONS MAP ESSENTIAL STEPS FOR INSTALLATION FLASHING LIGHT CONNECTION TRANSMITTERS "P"...
-
Page 3: Safety Instructions
STANDARDS TO FOLLOW TECHNICAL SPECIFICATIONS ATTENTION: The MC50BR is a monophasic control board com a control system via incorporated rádio, developed for the automation of electromechanical barriers. This product is certified in accordance with European Community (EC) safety standards. • Power supply 230V AC 50-60Hz •... - Page 4 02. THE CONTROL BOARD 02. THE CONTROL BOARD TECHNICAL SPECIFICATIONS PROGRAMMING PRE-RECOMENDATIONS 01 • Safety Edge LS • LED lit when the pedestrian push button is active 02 • Photocells LO • LED lit when the total push button is active 03 •...
-
Page 5: Installation
03. INSTALLATION 03. INSTALLATION ESSENTIAL STEPS FOR INSTALLATION TRANSMITTERS The installation process assumes that the barrier has already limit switches Transmitter programming for total opening. plates installed. For more information consult the barrier's manual. • PROGRAMMING TRANSMITTERS • ERASE TRANSMITTERS 01 •... - Page 6 03. INSTALLATION 03. INSTALLATION "P" MENU FUNCTIONS "E" MENU FUNCTIONS • We can only go into programming with a electrically closed barrier. • We can only go into programming with a electrically closed barrier. • To access the P menu •...
-
Page 7: Ramp Adjustment
04. PROGRAMMING "P" COURSE AUTOMATIC PROGRAMMING This menu allows you to set the barrier's working time. During the automatic programming, the barrier performs the following maneuvers: 1º if it is open, closes with deceleration 2º opens normally 03 • P1 appears. 3º... - Page 8 04. PROGRAMMING "P" 04. PROGRAMAR "P" SETTING STRENGTH AND SENSITIVITY TEMPO DE PAUSA P3 MENU INACCESSIBLE. 04. PROGRAMMING "P" PAUSE TIME If the control board has very high sensitivity values, you may see the LI error. After four attempts, the LI error will turn ER. You will have to wait 10 sec.
- Page 9 04. PROGRAMMING "P" 04. PROGRAMMING "P" PHOTOCELLS PROGRAMMING SAFETY BAND 00 (disables photocells) 00 (photocells during the closing) 00 (disables safety band) 00 (8k2 input) 00 (band during closure) 01 (ables photocells) 01 (photocells during the opening) 01 (ables safety band) 01 (NC input) 01 (band during opening) With the photocells activated,...
-
Page 10: Operating Logic
04. PROGRAMMING "P" 04. PROGRAMMING "P" OPERATING LOGIC FLASHING LIGHT Functioning in automatic Functioning in step by Functioning in Intermittent During movement of Courtesy light Electromagnet mode step mode condominium mode (opening and closing) the barrier (opening The light will remain With the barrier Does not accept orders 1st impulse - OPENS... - Page 11 04. PROGRAMMING "P" 05. PROGRAMMING "E" DISTANCE PROGRAMMING PRESENT MAN Present man Push button mode 01 (activates present man) distance PGM OFF distance PGM ON LS Button LO Button The motor only works if you hold This menu allows you to enable or disable down the pushbutton LS or LO.
-
Page 12: Soft Start
05. PROGRAMMING "E" 05. PROGRAMMING "E" SOFT START COURTESY LIGHT TIME 00 disabled function 01 enabled function This menu lets you set the time (1-99 minutes), that the courtesy light This menu allows you to enable / disable soft start. stays on after the closing of the barrier. - Page 13 05. PROGRAMMING "E" FOLLOW ME E4 MENU NOT AVAILABLE. E5 MENU NOT AVAILABLE. 05. PROGRAMMING "E" COURTESY LIGHT TIME 00 disabled function 01 enabled function This menu allows you to activate the option Follow me. With this function activated whenever the photocells detect the passage of a user/obstacle, the control board triggers the closing operation after 3 seconds.
- Page 14 05. PROGRAMMING "E" 05. PROGRAMMING "E" MANEUVER COUNTER RESET - RESTORE FACTORY VALUES This menu allows you to check how many complete maneuvers were performed by the By doing reset, all factory settings will be restored and all saved commands will be deleted. control board (complete maneuver it is understood by opening and closing).
-
Page 15: Display Indications
05. PROGRAMMING "E" 06. DISPLAY RGB OUTPUT DISPLAY INDICATIONS MENU DESCRIPTION MENU DESCRIPTION Continuous light Flashing light Pre-Flashlight Opening limit-switch enabled Inversion by effort The control board activates The control board activates The control board activates the output during the opening, the output during the opening, the flashing light output for 3 Closing limit-switch enabled... -
Page 16: Components Test
07. COMPONENTS TEST 07. COMPONENTS TEST SCHEME FOR CAPACITATOR INPUTS TEST To detect which components have problems in an electromechanical barrier installation, In the position corresponding to each transmitter input in low voltage, the control board has a LED to identify the condition of it. The LED on indicates that the input is closed, while the sometimes is necessary to conduct tests with a direct connection to a 110V or 230V LED off indicates that the input is open. -
Page 17: Troubleshooting
08. TROUBLESHOOTING INSTRUCTIONS FOR FINAL CONSUMERS/TECHNICIANS Anomaly Procedure Behavior Procedure II Discovering the origin of the problem • Motor • Make sure you have • Still not working. • Consult a qualified 1 • Open control box and check if 3 •... -
Page 18: Connection Scheme
09. CONNECTION SCHEME CONNECTIONS MAP See diagram on page 19 CLOSE OPEN... - Page 19 09. CONNECTION SCHEME FLASHING LIGHT CONNECTION To remove the LED strip it is The positioning is based on the only necessary to remove the existing letters of the LED strip. two connecting points. It is considered as incorrect posi- tion when the letters are inverted (with the light sensor on the left).
Need help?
Do you have a question about the MC50BR and is the answer not in the manual?
Questions and answers