The Default Setting Menu - Toshiba TDP-T100 Owner's Manual

Using the menus (Continued)

■ The default setting menu

This menu shows placement status and other settings.
Item
Projection Sets projection mode in accordance with Placement Style.
mode
(Standard)
No signal Set the time to wait for the power to be turned off after the last
power off operation is made with no input signal.
Off (not turned off)
Auto input Set whether the input with signals is only selected or not.
search
Power on
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto).
Lamp power
Sets the lamp power.
Fan mode
Sets the cooling fan speed.
Remote control
When two or more projectors are used and controlled by the remote
control respectively, this menu sets the code for the projector and the
remote control.
[ or : Enter setting mode]
Select from 1, 2, 3, 4]
Press [Cancel] to return.
Key lock
Lock the control panel buttons.
[ or : Enter setting mode]
Select On/Off] [
Press [Cancel] to return.
Reset all
Press . (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password
Password function
p.32
When [Password] is [On], the Password Setting screen is displayed.
Detailed description
[Auto input search]
[On]: Automatically searches the signals that
can be projected, and switches input
from the connected device that outputs
the video signals each time the INPUT
button is pressed. The input from the
connected device that outputs no video
signals is skipped.
[Off]: Displays the Input select menu.
Toggle with buttons and press
button. (The input without signals can be
selected.)
Description
p.21
(Rear) (Ceiling) (Rear ceiling)
30 min.
On
Manual
Low Standard
Standard
[ : Select item] [
[ :Confirm] [ :Select OK to end]
[ : Select item] [
:Confirm] [ :Select OK to end]
Yes
Off
Input select menu
Input select
Computer 1
Y/P /P 1
B R
Computer 2
Y/P /P 2
B R
Video
S-video
/ shows whether signal is
input or not.
40
[Power on]
Note that if [Power on] is set to [Auto], then if the power is supplied when restored
after a power outage, the projector will come on.
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the
cooling fan noise gets quieter.
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan
noise gets louder.) Set this option to use the projector, for example, at high altitude
(over 1,500 meters above sea level).
Off
• Do not set Fan mode to [High] when using the projector at a lower altitude.
[Remote control]
Auto
Sets a remote control code from 4 types. You can set each code respectively for up
to 4 projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
High
A remote control code is applied after the setting is done.
• You cannot operate the remote control if the codes of the projector and the
remote control do not match.
Remote control code setting for remote control
:
Remove the battery cover and set the same remote control code switch as the
projector. p.16
:
[Key lock]
Protect from operating errors by locking on the control panel buttons of the
No
projector. (The remote control operations are available.)
On
Control panel operations are locked after the setting is done, and accordingly
operation with the control panel buttons is disabled.
• To release the key lock, set the [Key Lock] to [Off] using remote control. Pressing
the [RETURN] button on the projector for 10 seconds also sets the [Key Lock] to
[Off]. (In the latter case, the LAMP, TEMP, and FAN indicators light in orange for 3
seconds.)
(Use a screwdriver with thin tip to set.)
41