Table of Contents
Advertisement
Quick Links
GETTING STARTED GUIDE
NI PXImc Devices
NI PXIe-8830mc PXImc Processor Module
This document includes instructions for installing and configuring your NI PXIe-8830mc
PXImc processor module.
Contents
Products Covered...................................................................................................................... 1
Conventions.............................................................................................................................. 2
Getting Started.......................................................................................................................... 2
Unpacking......................................................................................................................... 2
Electrical........................................................................................................................... 2
Preparing the Environment............................................................................................... 3
Hardware Installation........................................................................................................ 3
Powering On the PXImc System...................................................................................... 4
Powering Off the PXImc System......................................................................................4
Software Installation and Configuration........................................................................... 4
LabVIEW RT Installation................................................................................................. 4
NI PXIe-8830mc Front Panel........................................................................................... 8
Removing the NI PXIe-8830mc from a PXI Express Chassis..........................................9
Cleaning............................................................................................................................ 9
Common Configuration Questions......................................................................................... 10
General Questions........................................................................................................... 10
Upgrade Information.......................................................................................................10
Troubleshooting.......................................................................................................................11
What if the processor module does not boot?................................................................. 11
My system boots fine as long as a particular module is not in my chassis..................... 12
My CMOS is corrupted. How do I set it back to default?.............................................. 12
Worldwide Support and Services............................................................................................ 13
Products Covered
This document covers the following products:
•
NI PXIe-8830mc (156252x-011L)
Note
Following the model number above is the specific NI assembly number in
parentheses. Ensure that the specifications of interest match the NI assembly number
printed on the board. x denotes all letter revisions of the assembly.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for National Instruments PXImc Series
Summary of Contents for National Instruments PXImc Series
-
Page 1: Table Of Contents
GETTING STARTED GUIDE NI PXImc Devices NI PXIe-8830mc PXImc Processor Module This document includes instructions for installing and configuring your NI PXIe-8830mc PXImc processor module. Contents Products Covered........................1 Conventions..........................2 Getting Started.......................... 2 Unpacking......................... 2 Electrical........................... 2 Preparing the Environment....................3 Hardware Installation...................... -
Page 2: Conventions
Remove the device from the package and inspect the device for loose components or any other sign of damage. Notify National Instruments if the device appears damaged in any way. Do not install a damaged device into your chassis. Electrical... -
Page 3: Preparing The Environment
Identify the slot in which the NI PXIe-8830mc will be installed in the chassis. Refer to the following table to determine which slot types the NI PXIe-8830mc is compatible with. NI PXImc Devices Getting Started Guide | © National Instruments | 3... -
Page 4: Powering On The Pximc System
Table 1. NI PXIe-8830mc Slot Type Compatibility PXI Express Chassis NI PXI Express Product Controller Peripheral Hybrid NI PXIe-8830mc — Align the NI PXIe-8830mc with the card guides on the top and bottom of the slot. Hold the handle as you slowly slide the module into the chassis until the handle catches on the injector/ejector rail. - Page 5 LabVIEW Real-Time. Note Refer to Getting Started with the LabVIEW Real-Time Module on your host computer for more information about setting up your RT target. NI PXImc Devices Getting Started Guide | © National Instruments | 5...
- Page 6 LabVIEW RT Configuration Switches Use the LabVIEW RT configuration switches to configure LabVIEW RT if it is installed on the processor module. If you are not using LabVIEW RT, these switches should remain in the OFF position. The processor module reads these switches only after a system reset. The NI PXIe-8830mc processor module includes the following LabVIEW RT configuration switches: •...
- Page 7 Figure 1. LabVIEW RT Configuration Switches 1. Switch 1—Boot LabVIEW RT 3. Switch 3—Disable Startup VI 2. Switch 2—Boot Safe Mode 4. Switch 4—Reset IP Address NI PXImc Devices Getting Started Guide | © National Instruments | 7...
-
Page 8: Ni Pxie-8830Mc Front Panel
NI PXIe-8830mc Front Panel The following figure shows the front panel layout of the NI PXIe-8830mc. Figure 2. NI PXIe-8830mc Front Panel 1. Reset Button 5. User 2 LED 2. Ethernet Connector 6. PWR OK/FAULT LED 3. USB Connectors 7. Drive LED 4. -
Page 9: Removing The Ni Pxie-8830Mc From A Pxi Express Chassis
Use a dry, low-velocity stream of air to clean the NI PXIe-8830mc processor module. If needed, use a soft, nonmetallic brush for cleaning around components. Make sure that the device is completely dry and free from contaminants before returning it to service. NI PXImc Devices Getting Started Guide | © National Instruments | 9... -
Page 10: Common Configuration Questions
Remove the installed DDR4 SO-DIMM module, if necessary. Install the new DDR4 SO-DIMM module into the slot. NI PXIe-8830mc System Memory Information National Instruments offers the following types of SO-DIMMs for use with the NI PXIe-8830mc processor module. Note National Instruments has tested and verified that the DDR3 SO-DIMMs we sell work with the NI PXIe-8830mc processor module. -
Page 11: Troubleshooting
What has changed about the system? Did you recently move the system? Was there electrical storm activity? Did you recently add a new module, memory chip, or piece of software? • Refer to your chassis documentation for additional troubleshooting steps. NI PXImc Devices Getting Started Guide | © National Instruments | 11... -
Page 12: My System Boots Fine As Long As A Particular Module Is Not In My Chassis
Things to Try: • Make sure the chassis is plugged in to a working power source. • Check any fuses or circuit breakers in the chassis or other power supply (possibly a UPS). • Make sure the processor module is firmly seated in the chassis. •... -
Page 13: Worldwide Support And Services
Figure 4. Clearing the CMOS Contents 1. Push-Button Switch SW1 Worldwide Support and Services The National Instruments website is your complete resource for technical support. At ni.com/ support, you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers. - Page 14 Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the file on your media, or the National Instruments Patent Notice at .
Need help?
Do you have a question about the PXImc Series and is the answer not in the manual?
Questions and answers