Nortel 8660 SDM Installing page 11

Figures
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Figure 24
Figure 25
Figure 26
Figure 27
Figure 28
Figure 29
SDM FW4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SDM FW4 faceplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8660 SDM FW4 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
iSD LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Removing a filler panel from an 8003, 8006, or 8010 chassis . . . . . . . . . 29
Removing a filler panel from an 8010co chassis . . . . . . . . . . . . . . . . . . . 30
Loosening screws on the SDM FW4: 8003, 8006, or 8010 chassis . . . . . 33
Loosening screws on the SDM FW4: 8010co chassis . . . . . . . . . . . . . . . 33
Ejecting the SDM FW4: 8003, 8006, or 8010 chassis . . . . . . . . . . . . . . . 34
Ejecting the SDM FW4: 8010co chassis . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Removing an SDM FW4: 8003, 8006, or 8010 chassis . . . . . . . . . . . . . . 35
Removing an SDM FW4: 8010co chassis . . . . . . . . . . . . . . . . . . . . . . . . 36
Installing an SDM FW4: 8003, 8006, or 8010 chassis . . . . . . . . . . . . . . . 38
Installing an SDM FW4: 8010co chassis . . . . . . . . . . . . . . . . . . . . . . . . . 38
Seating the backplane connectors: 8003, 8006, or 8010 chassis . . . . . . 39
Seating the backplane connectors: 8010co chassis . . . . . . . . . . . . . . . . . 39
Securing the SDM FW4 in the chassis: 8003, 8006, or 8010 chassis . . . 40
Securing the SDM FW4 in the chassis: 8010co chassis . . . . . . . . . . . . . 41
Loosening the disk drive captive screw . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Sliding the disk drive tabs from the slots . . . . . . . . . . . . . . . . . . . . . . . . . 45
Disk drive connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Connecting the disk drive cable to the disk connector . . . . . . . . . . . . . . . 47
Connecting the disk drive cable to the PrPMC connector . . . . . . . . . . . . 48
Sliding the disk drive tabs into the slots on the SDM FW2 tray . . . . . . . . 48
Fastening the disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Locating the installed PrPMC on an SDM FW4 . . . . . . . . . . . . . . . . . . . . 53
SDM FW4 with components facing up . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Removing the stiffener screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SDM FW4 with components facing down . . . . . . . . . . . . . . . . . . . . . . . . . 54
Installing the 8660 Service Delivery Module (SDM)
11