Download Print this page

Advertisement

Quick Links

Advertisement

loading

Subscribe to Our Youtube Channel

Summary of Contents for Cisco USC 5030

  • Page 1: Table Of Contents

    Cisco USC 5030 Installation Guide Cisco USC 5030 Installation Guide About Your USC 5030 Before You Begin Connect Your Cisco USC 5030 Verifying Your Installation Safety Instructions...
  • Page 2: Cisco Usc 5030 Installation Guide

    About Your USC 5030 The Cisco USC 5030 chassis is uniquely designed to hold either one or two Cisco USC enterprise licensed small cell modules. Currently installation of one small cell module is supported. For a 3G enterprise solution, it is populated with the Cisco USC 5310 (Band 1 or Band 2/5).
  • Page 3 Install a USC 5310 small cell module into the USC 5030: a) Align the module connector with the port connector on the back of the USC 5030 and click the module into place. b) Screw down the thumb screws on the module.
  • Page 4 Step 3 Connect one end of the network cable to the USC 5030 Ethernet port and the other end to your broadband router or cable modem. Step 4 Connect the power adapter to the power port and to an AC power source.
  • Page 5: Verifying Your Installation

    Verifying Your Installation Verify Your Cisco USC 5030 Installation The LED display is located on the top of your Cisco USC 5030 and indicates whether modules are installed and operational or not. Figure 2: Cisco USC 5030 LED Status LED...
  • Page 6 Verify Your Small Cell Module Installation After the USC 5310 module is installed in the USC 5030 chassis and powered up, it takes approximately ten minutes for the module to initialize, download any necessary software and configuration information, configure the radio frequency (RF) parameters, and come into service.
  • Page 7: Safety Instructions

    RF issue, cannot select an RF profile—Verify whether another small cell is located in close proximity and if so, relocate the small cell Provisioning failure—Contact operator Safety Instructions Translated versions of the following safety warnings are provided in Cisco USC 5030 Regulatory Compliance and Safety Information, located on Cisco.com.
  • Page 8 Statement 1071—Warning Definition Warning Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
  • Page 9 Warning Statement 1005—Circuit Breaker Warning This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 10-15A, 100-240VAC Attention Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de l'installation électrique du local.
  • Page 10 LAN associées, doivent être installés à l'intérieur d'un même bâtiment. The USC 5030 is suitable for operation in a building's environmental air space, such as above suspended Note ceilings, in accordance with Section 300-22(C) of the National Electrical Code (NEC) and Sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 1, C22.1.
  • Page 11 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.
  • Page 12 Cisco Systems, Inc. Cisco Systems (USA) Pte. Ltd. Cisco Systems International BV San Jose, CA 95134-1706 Singapore Amsterdam, The Netherlands Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/offices.