Related Manuals for Zigen ZIG-POEWP-100TX
Summary of Contents for Zigen ZIG-POEWP-100TX
- Page 1 ZIG-POEWP-100TX HDMI/VGA Auto-switching wall plate HDBase-T Transmitter Over Single CAT5e/6/7 100m, IEEE POE Powered, 4K, Audio, IR, RS232, LAN, ZigNet...
- Page 2 Important Safety Instructions 1. Do not use this product near water. 2. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 3. Do not install or place this product near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Page 3 Return Policy If you would like to return a Zigen product, it can be done within 30 days of purchase for a full refund, less shipping and handling. Zigen will not be responsible for shipping and handling of product returns. Returns will only be accepted of products with proof of purchase, products in the original packaging with zero to minimal use and a Return Merchandise Authorization RMA number provided by Zigen.
- Page 4 Contacting Zigen Technical Support Tel: (818) 654-5252 Fax: (818) 654-5355 8:00AM - 5:00PM (PST) Email info@zigencorp.com www.zigencorp.com Mailing Address Zigen Corp. c/o Customer Service 16135 Wyandotte Street Lake Balboa CA 91406...
- Page 5 Features • HDMI and VGA w/Audio input – VGA can be configured as Component or Composite video. • Auto-Switching function – if you remove an active source – and another source is connected then it will switch to the new source immediately. •...
- Page 6 Specifications Inputs HDMI x 1 VGA x 1 – multi-port – supports YPbPr and Composite video 3.5mm Audio port – follows VGA port Power – On back – 5VDC direct or IEEE POE from RX or switch Outputs HDBasetT x 1 – RJ45 – note port is dual use so it can be used as an Ethernet port when programming or controlling the device.
- Page 7 Packing List The ZIG-POEWP-100TX is a wall plate 100 meter (328 feet) HDBaseT transmitter. It can be powered with a 5 VDC supply or from a POE RX device that it is connected to like a ZIG- PS-61 or ZIG-POE-RXAV. It can be used stand-alone as an HDBaseT wall-plate transmitter, but really shines when paired with the ZIGPOE-RXAV receiver/scaler &...
-
Page 8: Table Of Contents
Table of Contents Introduction Front Panel ....................... 9 Back Panel ......................10 Connection Example ………………………………………………………….….……... 11 System Control Accessing ZigNet ....................12 Using ZigNet ………………………………………………………………….….………. 13 ZigNet: Control Page ……………………………………………………..……… 14-16 ZigNet: Diagnostics Page …………………………………………………...………. 17-19 ZigNet: Admin Page ………………………………………………………………….. 20-21 RXAV Commands ………………………………………………………….…………... -
Page 9: Front Panel
Front Panel Source select – turns blue when HDMI is selected and off when VGA is selected. Source selection can happen 4 ways: a. First source connected automatically is active and sent to display. b. By pushing this button the source will toggle. c. -
Page 10: Back Panel
Back Panel HDBaseT output/LAN Port (fallback) connection – Connect RJ45 up to 100 meters (328 feet) CAT5e, 6, 6a. This is the connection to an HDBaseT receiver such as the ZIG-POE-RXAV or ZIG-PS-61. You can also use this connection when accessing via WebOS. -
Page 11: Connection Example
Connection Example Example is showing our HDBaseT transmitter (ZIG-POEWP-100) connected to the HDBaseT receiver (ZIG- POE-RXAV) Amplified audio output for direct connection to speakers, LAN ports for almost anything you choose and for controlling/setting up the devices, relays, a 4K scaler and IR and RS232 control and functionality. -
Page 12: Accessing Zignet
Accessing ZigNet ZigNet provides easy management of all features used by the ZIG-POEWP-100TX. ZigNet is a highly functional web server that is accessible either remotely across the Internet or directly with a connection between a personal computer on a local area network, or a connection directly to the Ethernet connector on the back panel of the unit. -
Page 13: Using Zignet
Using ZigNet Navigation Bar From the navigation bar, select the appropriate link to get to the corresponding page. The blue bar below the link indicates that the page is selected. Control Page Allows the user to switch the inputs for the outputs, change EDID settings and adjust audio settings. -
Page 14: Zignet: Control Page
ZigNet: Control Page Source Management Refresh: Refreshes the current source and connection status Change Source: Click the desired input (source). The active input is indicated by a green button. - Page 15 ZigNet: Control Page (continued) RS-232 commands: Zigen RX AV baud rate Change baud rate for RXAV. Coming soon in future RXAV revisions. Disclaimer: RXAV with current firmware baud rates need to be changed on the rxav web interface. RS-232 commands can take ASCII, HEX, or a mixture of ASCII and HEX.
- Page 16 ZigNet: Control Page (continued) We can delay a command by using the Delay keyword. The formatting is as follows: Delay-xxxx, where “xxxx” is the delay in milliseconds. Commands not specified will be ignored. Example: ASCII will ignore HEX values. Test: Tests the command in the input box Save: Save the command in the input box.
-
Page 17: Zignet: Diagnostics Page
ZigNet: Diagnostics Page Inputs Section Diagnostics displays the status of the inputs. If an input is active and connected, the source will display connected. Outputs Section The output displays the status of the Valens chip, further details can be found below System Monitoring Displays runtime in between factory resets. - Page 18 ZigNet: Diagnostics Page (continued) Link Status: Type Description No Link The device is currently not connected to LAN HDBaseT The device is receiving and outputting a video source Low Power Partial Standby Mode. The device is currently not outputting a Functionality video source.
- Page 19 ZigNet: Diagnostics Page (continued) Cable Length: Approximates the cable length. If the wall plate is in standby, the cable length will not be displayed, instead will show Low Power Mode. Cable Length Display Standy Modes Low Power Mode 0-20 meters <...
-
Page 20: Zignet: Admin Page
ZigNet: Admin Page User Notes Allows the user to write and save notes for system configuration. Device Settings and Information Hostname: type desired host name and press Change Name. Manual IP Address: Use these fields to change the IP address used in static IP mode and the IP address used in DCHP mode when no IP address can be obtained. - Page 21 ZigNet: Admin Page (continued) Change Password To change the password, type the current password, the desired new password and confirm the new password.
-
Page 22: Rxav Commands
Provides firmware info release number, revision number, build date and serial number. Discovery @rxav-xxxx disco Provides a list of other Zigen products on the network Set Volume @rxav-xxxx vol <-136 - 10> Sets a fixed volume in dB on the... - Page 23 RXAV Commands (continued) To address a single unit, replace “xxxx” with the last four serial number located on the sticker. To address a cluster of RXAV units, use only “rxav” Relay 1 Command Example: To power ON relay 1 on the RXAV, use command: “@rxav-xxxx rel1 on \n” To power OFF relay 1 on the RXAV, use command: “@rxav-xxxx rel1 off \n”...
-
Page 24: Poewp-100Tx Commands
POEWP-100TX Commands Command Syntax Description Help @poewp-xxxx help Shows a list of available commands Uptime @poewp-xxxx uptime Shows elapsed time. Version @poewp-xxxx version Provides firmware info release number, revision number, build date and serial number. Source @poewp-xxxx insel Sets source to HDMI or VGA Switching <hdmi/vga>... -
Page 25: Telnet Ip Commands
Telnet IP Commands Command Syntax Description Help poewp-xxxx help Shows a list of available commands Uptime poewp-xxxx uptime Shows elapsed time. Version poewp-xxxx version Provides firmware info release number, revision number, build date and serial number. Sets source to HDMI or VGA Source poewp-xxxx insel Switching... -
Page 26: Diagnostics
Diagnostics Specifications Source: Indicates if a source is connected to the unit. Video Link: Indicates if video is being passed from the source. Source Type: Indicates if the source is connected through an HDMI or DVI interface. 18G Signal: Indicates if the HDMI signal being transmitted is greater than 3.4 GBPS. HDCP Status: Indicates the HDCP authentication status. -
Page 27: Glossary
UHD – Ultra High Definition. This is commonly referred to the video format 3840 x 2160. VESA – Video Electronics Standards Association is a technical standards organization for computer display formats. ZigNet – Proprietary web control developed by Zigen, Inc.