Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Nice Slight
Summary of Contents for Nice Slight
- Page 1 Slight Sliding gate opener Instructions and warnings for installation and use...
- Page 2 20÷30 0 ÷ 50 0 ÷ 50...
- Page 4 LUCYB MOFB MOSE OPEN S.C.A CLOSE 24V 4W NC NO NO NC FLASH S.C.A BLUEBUS STOP P.P. OPEN CLOSE...
- Page 6 LUCYB LUCYB MOFB MOSE OPEN STOP S.C.A S.C.A CLOSE 24V 4W 24V 4W NC NO NO NC FLASH S.C.A BLUEBUS STOP P.P. OPEN CLOSE FLASH S.C.A BLUEBUS STOP P.P. OPEN CLOSE BLUEBUS BLUEBUS MASTER SLAVE...
- Page 9 9.1.5 - Slight in “Slave” mode ....... . . 11...
- Page 10 1 and 2. If powered from the grid, Slight can host a buffer battery (mod. PS124, optional on the friction as well as other correlated factors, such as ice, that could inter- accessory) which permits the automation mechanism to continue to perform fere with the movement of the leaf.
- Page 11 Main movable edge quent damage to the electronic circuits. Slight Secondary movable edge (optional) 30 m ( 30m ( 30m ( –...
- Page 12 “Instructions and Warnings for users of the are connected in parallel using two conductors only, through which both the Slight gear motor”. Position the leaf in a closing position, leaving it at least 50cm from the mation about BlueBUS see also paragraph “9.1.1 BlueBUS”.
- Page 13 please see paragraph “9.1.6 Recognition of other devices” in order to per- form a new recognition. S.C.A. output on the control unit. In order to program these functions, refer to paragraph “8.5 Level 2 programming”. urement is required to calculate the deceleration points and the partial opening point.
- Page 14 switch, it is possible to tap power as shown in manoeuvre counter and maintenance warning system; see paragraph “9.2.3 100mA. – 24Vcc sponding maintenance schedules. 2. Disconnect all power supplies (including any buffer batteries). parts which are below the required standard. components;...
- Page 15 control unit, a number of programmable functions are available. [ ] [Set] [ ] and are used by means of 8 LEDs: In this case, each of the LEDs indicates one function; if it is lit the func- most automations. the parameters can be adjusted on a scale of values (from 1 to 8).In this case, each of the LEDs indicates the set value (there are 8 pos-...
- Page 16 es made up to that time. Press and hold the “Set Release the “Set ” or “ Press the “Set 10 s ” matically memorising the changes made up to that time. 5 seconds Adjusts the pause time, namely the time which lapses before automatic 15 seconds closure.
- Page 17 0.5 mt Adjusts the measurement of the par- tial opening. Partial opening can be 1 mt controlled with the 2nd radio com- 1.5 mt function is present, this becomes 2 mt 2.5 mt 3 mt 3.4 mt 4 mt Automatic (depending on the severity of the manoeuvre) Adjusts the number of manoeuvres after which it signals the mainte- 1000...
- Page 18 ” to 60 seconds (input on L1 and level on L5) and reducing the “ Press and hold the “Set Press and hold the “Set Press the Release the “Set Press the Press and hold the “Set Press the 11. Release the “Set 10 s resistance in series any time.
- Page 19 when leaving the factory). BUS. in the Master e Slave modes, you must follow these opera- tions: is to function as Slave or Master; when choosing, one must consider the con- venience of the connections and the fact that the Step-by-Step command of Each time a photocell is added or removed the control unit must go through the Slave only allows the Slave leaf to be opened fully.
- Page 20 a distance. to control an opening manoeuvre when the “Step-by-Step” command lasts is a description of the association between the radio receiver output and the In the event that one of the safety devices is not functioning properly or is out of use, it is still possible to command and move the gate in “Man present”...
- Page 21 Press and hold the “Set Release the “Set Press the “ ” or “ Press and hold the “Set light up; Press and immediately release the “ ” and “ ..Release the “Set After the maintenance of the system has been performed the manoeuvre coun- ter must be reset.
- Page 22 occur during the installation stage or in case of failure. replace the fuses with others having the same current rating and characteristics. if necessary increase the force due to the lamp; in this case replace the lamp with one having the same characteristics; if there is no circuited.
- Page 23 Bluebus error At the starting of the manoeuvre, the devices connected to the recognition process. At the starting of the manoeuvre, one or more photocells do not 1 second pause when there is an obstacle impeding the movement. identify the cause. 1 second pause 1 second pause vated;...
- Page 24 Paragraph 9.1.6) (refer to Paragraph “9.1.6 Recognition of the devices”) (refer to Paragraph “6.4 Recognition of the length of the leaf”). (refer to Paragraph “6.4 Recognition of the length of the leaf”). – English...
- Page 25 tions to products at any time when deemed necessary, maintaining the same intended use and functionality. Electromechanical gear motor for the automatic movement of sliding gates for residential use, complete with electronic control unit Z: 15; Module: 4; Step: 12.6 mm; Primitive diameter: 60mm 12Nm;...
- Page 26 NICE S.p.a. Nice s.p.a. Electromechanical gear motor with incorporated control unit above complies with the provisions of the following directives: EEC, in accordance with following harmonised standards: EN 61000-6-2:2005, EN 61000-6-3:2007 In addition, the product conforms to the following directive in accordance with the provisions applicable to partly completed machinery: 1.5.2- 1.5.5- 1.5.6- 1.5.7- 1.5.8- 1.5.10- 1.5.11...
- Page 27 If you wish to install another automation system in your home, call your old installation technician and use Nice products. You will get the services of a specialist and the most advanced prod- confident that you will be well satisfied with your new sy stem: for any present or future requirements, please contact your reliable installation technician.
- Page 28 Nice SpA Oderzo TV Italia www.niceforyou.com info@niceforyou.com...
Need help?
Do you have a question about the Slight and is the answer not in the manual?
Questions and answers