Advertisement
Caution
- This appliance is not
washable. Never immerse the
appliance in water and do not
rinse it under the tap (Fig. 2).
- Only use this appliance for its
intended purpose as shown
in the user manual.
- For hygienic reasons, the
appliance should only be
used by one person.
- Never use compressed air,
scouring pads, abrasive
cleaning agents or aggressive
liquids such as petrol or
acetone to clean the
appliance.
- Do not use the supply unit in
or near wall sockets that
contain an electric air
freshener to prevent
irreparable damage to the
supply unit.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
General
- The supply unit is suitable for mains voltages
ranging from 100 to 240 volts.
- The supply unit transforms 100-240 volts to a
safe low voltage of less than 24 volts.
- Maximum noise level: Lc = 75 dB(A).
Charging
Charge the appliance fully before you use it for the
first time and after a long period of disuse.
It takes approximately 10 hours to fully charge the
appliance. When it is fully charged, the appliance
has a cordless operating time of up to 45 minutes.
1
Make sure the appliance is switched off.
2 Insert the small plug into the appliance (Fig. 3).
3 Put the supply unit in the wall socket.
- The charging light on the supply unit lights up
green to indicate that the product is charging.
Note: The charging light on the supply unit does
not change color and does not go out when the
product is fully charged.
4 After charging, remove the supply unit from the
wall socket and pull the small plug out of the
appliance.
Optimizing the lifetime of the
rechargeable battery
When you have charged the appliance for the first
time, we advise you to use it until the battery is
completely empty. Continue to use the appliance
until the motor almost stops running during a
session. Then recharge the battery. Follow this
procedure at least twice a year.
- Slide the on/off button up to switch the
product on or off (Fig. 4).
Using the appliance
Note: Switch off and clean the appliance after each
use.
Always comb the beard and/or moustache with a
fine comb before you start trimming.
Be careful when you trim for the first time. Do
not move the trimmer too fast. Make smooth
and gentle movements.
Trimming with comb
Note: When you trim for the first time, start at the
highest length setting to familiarize yourself with
the appliance.
Use the trimming comb attached to the cutting
element to trim your beard and moustache in your
preferred style. Turn the zoom wheel to choose
from 11 length settings ranging from 0.5 mm to
10 mm (1/32 in. to 13/32 in.).
1
Slide the trimming comb straight into the
guiding groove of the appliance (Fig. 5).
2 Turn the zoom wheel to the desired setting (Fig.
6). The desired hair length setting is shown in
the center of the zoom wheel.
3 Switch on the appliance.
4 To trim most effectively, move the appliance
against the hair growth direction. Make sure
that the surface of the comb always stays in
contact with the skin.
Note: Since all hairs do not grow in the same
direction, you may want to try different
trimming positions (i.e. upwards, downwards, or
across). Practice is best for optimum results.
5 Regularly remove cut hair from the comb. If a lot
of hair has accumulated in the comb, remove it
from the appliance and blow and/or shake out
the hairs (Fig. 7). The selected hair length setting
does not change when the comb is removed.
6 Switch off and clean the appliance after each
use.
Trimming for 'stubble look'
1
Be certain trimming comb is attached to the
appliance and use setting 0.5mm (1/32in.) to
create a 'stubble look' trim (Fig. 8).
Advertisement
