Advertisement
Quick Links
4410BFFR_FTN_A
LK4410BFFR_FTN_A
Owners Manual
Model 4410BFFR Tubular Bottle Filler Fountain
with Sanitary Freeze Resistant Single Valve Control Assembly
INSTALLER
4410BFFR Fountains are among the easiest to install Fountains on the market today. To assure
you install these models easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS
BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE
WITH PLUMBING, ELECTRICAL, AND OTHER APPLICABLE CODES. After installation, leave
these instructions with the Fountain for future reference.
PAGE 1
1000004253 (Rev. A - 08/17)
Advertisement
Related Manuals for Elkay 4410BFFR
Summary of Contents for Elkay 4410BFFR
- Page 1 Sanitary Freeze Resistant Single Valve Control Assembly INSTALLER 4410BFFR Fountains are among the easiest to install Fountains on the market today. To assure you install these models easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER APPLICABLE CODES.
-
Page 2: Installation Instructions
4410BFFR_FTN_A LK4410BFFR_FTN_A INSTALLATION INSTRUCTIONS IMPORTANT ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON IMPORTANT! INSTALLER PLEASE NOTE. THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE BUILDING. - Page 3 4410BFFR_FTN_A LK4410BFFR_FTN_A SUGGESTED SITE PREPARATION DETAIL FOR THE 4410BFFR FTN. WHEN USING THE SANITARYFR1 VALVE 4" PVC 1/4 BEND 1-1/2" DRAIN TUBE (SUPPLIED BY INSTALLER) (SUPPLIED BY INSTALLER) 4" PVC PIPE (SUPPLIED BY INSTALLER) CONCRETE SLAB CLEANOUT PLUG FOR ACCESS 4"...
- Page 4 4410BFFR_FTN_A LK4410BFFR_FTN_A SUGGESTED SITE PREPARATION DETAIL FOR THE 4410BFFR FTN. WHEN USING THE SANITARYFR1 VALVE O 14" 356mm (6) 1/2" (13mm) DIA. HOLES EQUALLY SPACED ON A 12" ( 305mm ) BOLT CENTER 1-1/4 DRAIN TUBE SUPPLIED WITH FTN. AIR GAP ASSY.
- Page 5 4410BFFR_FTN_A LK4410BFFR_FTN_A FOUNTAIN CONNECTIONS PLUMBING CONDUIT (BY INSTALLER) TO VALVE FIG. 3 INSTRUCTIONS FOR CONNECTING TUBES FROM VALVE TO FOUNTAIN Step 1 - Insert the 1/8” O.D. tube (Label A) into the connector (provided with fountain). Insert the 1/8” O.D. tube coming from the fountain push button actuator into the connector.
- Page 6 4410BFFR_FTN_A LK4410BFFR_FTN_A 3, 11 FIG. 4 FIG. 5 1000004253 (Rev. A - 08/17) PAGE 6...
-
Page 7: Parts List
4410BFFR_FTN_A LK4410BFFR_FTN_A The Following Items are included with the SanitaryFR1 Valve PARTS LIST ITEM NO. PART NO. DESCRIPTION 110175443890 Hex Nut - 3/8-16 45806C Single Valve 50986C Regulator Holder 56082C Regulator Nut 56092C Poly Tubing - 1/4” (Cut To Length) - To Bubbler 56123C Poly Tubing - 1/8”... -
Page 8: Troubleshooting And Maintenance
4410BFFR_FTN_A LK4410BFFR_FTN_A TROUBLESHOOTING AND MAINTENANCE Insufficient Bubbler Flow: Check that the shut-off valve is wide open. Verify minimum 20 PSI supply pressure. Clean inlet strainer screen located in the valve body. Clean rubber orifice in flow control located below frost line in bushing between barb fitting and valve. No Flow: Check for leaks in the air tubing going from the push button to the valve. Make sure the air tubing compression nut is hand tight. Disconnect air tube from push button. Place finger over air outlet. Push button to test diaphragm. Tighten diaphragm cap screws. Replace diaphragm if necessary. - Page 9 4410BFFR_FTN_A LK4410BFFR_FTN_A 21, 22 Included with Sanitary Valve PAGE 9 1000004253 (Rev. A - 08/17)
- Page 10 Kit - VR Torx Screw/Bit 28703C Blank Nameplate Insert (only) 28703C-LK LK4410BFFR Nameplate Insert (only) 28091C-HT 4410BFFR Nameplate Insert (only) 98686C Kit - (BF) Waterway/Nipple/Gasket/Tubes/Ftgs *FINISH COLOR OPTIONS – Choose color option to 98679C Kit - Nozzle/Aerator/Gasket/Pin/Key complete your model number, add as suffix example:...