Table of Contents
Advertisement
Quick Links
f i r e - p a r t s . c o m
Warning:
Improper installation, adjustment,
alteration, service or maintenance can cause
injury or property damage. Refer to this
manual. For assistance or additional
information consult a qualified installer,
service agency or the gas supplier.
What To Do If You Smell Gas:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
For Your Safety:
Do not store or use gasoline
or other flammable vapors
and liquids in the vicinity of
this or any other appliance.
Installation
Operation &
Maintenance
SP28-F2
5" B-Vented
Gas Fireplaces
Check local codes and
n
read all instructions
prior to installation.
Leave this manual with
n
the owner.
APPROVED FOR
USE IN BC ONLY
Advertisement
Table of Contents
Related Manuals for Montigo SP28-F2
Summary of Contents for Montigo SP28-F2
- Page 1 Installation Operation & Maintenance SP28-F2 5" B-Vented Gas Fireplaces f i r e - p a r t s . c o m Warning: For Your Safety: Check local codes and Improper installation, adjustment, Do not store or use gasoline...
-
Page 2: Table Of Contents
Installing the Gasline ............4 The SP28-F2 Series is certified in British Columbia only which is The Remote Switch ............4 upgradable to the EP28-S2 insert, which is certified in the US and Canada as a Vented Gas Fireplace Heater (ANSI Z21.88 - 2000 /... -
Page 3: Installation
SP28-F2 Modular Series Fireplace Installation Installing The Fireplace Shell Framing The fireplace may be installed in any location that is free of air conditioning ducts, electrical wiring and plumbing. Safety, as well as For protection against freezing temperatures, it is recommended that efficiency of operation, must be considered when selecting the fireplace outer walls of the chase be insulated with a vapour barrier. -
Page 4: Installing The Gasline
SP28-F2 Modular Series Fireplace Installation Installing The Remote Switch Installing The Gas Line The EP28 Series' gas valve, located behind the lower trim, may be The gas line must be installed before finishing the fireplace. Natural Gas connected to a wall switch. The valve generates its own power. This is a requires a minimum inlet gas supply pressure of 5.5"... -
Page 5: Facing
SP28-F2 Modular Series Fireplace Installation Finishing Around the Fireplace Mantels & Surrounds Combustible mantels and mouldings may be safely installed over the top NOTE: Mantel clearances shown are for fire hazard prevention. and on the front of the fireplace provided that they do not project beyond New technology, to meet consumer and government demands for the shaded area shown in Figure 5. -
Page 6: Installing The Decorative Burner Tray
SP28-F2 Modular Series Fireplace Installation Installing Decorative Burner Trays The burner tray may be installed/upgraded before or after the EP28 outer shell has been installed. 1. Remove the lower trims. 2. If you are converting or upgrading an EP28 Series fireplace which has doors installed, you must first remove the doors. -
Page 7: Installing The Logset
SP28-F2 Modular Series Fireplace Installation EP28-F2 Logset Heat Circulating Blowers This model are supplied with five ceramic fibre logs and a package of Some EP-28 Series decorative fireplaces may be equipped with an silica sand. Unpack the logs and handle them very carefully. -
Page 8: Adjusting The Optional Doors
SP28-F2 Modular Series Fireplace Installation Optional Doors Upgrading to the -S2 Heating Insert EP28 Series Decorative Models come standard with a firescreen, and may be fitted with one of the following optional door kits: 1. Remove the upper and lower trims. - Page 9 SP28-F2 Modular Series Fireplace Installation 6. Cut the front bar to allow clearance to install the Heating Insert Using Install the Insert by pushing it all the way back inside the shell as a hacksaw, make the cut approximately 2" in from the side of the shown in figure 19.
- Page 10 SP28-F2 Modular Series Fireplace Installation 10. Reconnect gas line by following the information on page 4. 14. Remove the glass door as shown in Figure 23. Remove the plastic shipping ties and padding from the two bottom logs. Install the top 11.
-
Page 11: Operation
SP28-F2 Modular Series Fireplace Operation - Model EP28 EP28-4 with Continuous Pilot For Your Safety - READ BEFORE LIGHTING: WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. -
Page 12: Maintenance
SP28-F2 Modular Series Fireplace Maintenance CAUTION Gas Control Valve Fireplace gas control must be in the “OFF” position and pilot and main burners extinguished when cleaning appliance with a vacuum. Glass and logs can get very hot. Handle only when cool. - Page 13 SP28-F2 Modular Series Fireplace Maintenance Pilot Burner Adjustment Troubleshooting EP28-4 1. Determine which pilot is installed in the fireplace based on figures The following is a troubleshooting chart of possible problems: 25a and 25b. PROBLEM CORRECTIVE ACTION 2. Locate Pilot Adjustment Screw. (See figures 24a, 24b, and 24c.)
-
Page 14: Warranty
The Warranty The Companies warrants the Montigo Gas Appliance to be free from defects in materials and workmanship at the time of manufacture. On the Montigo, there is a ten- year warranty on the firebox and its components, a five-year warranty on the main burner and pilot burner, and a one-year warranty on the gas control valve and fibre logs. - Page 15 SP28-F2 Modular Series Fireplace Notes f i r e - p a r t s . c o m XG0318 Page 15...
- Page 16 - p a r t s . c o m XG0318 Rev. 00 03/2003 Canadian Heating Products Inc. Montigo Del Ray Corp. Ferndale, WA 98248 Langley, BC V4W 4A1...