Advertisement
Adjusting the time and calendar manually
Setting the time
1.
Pull the crown out to position
2.
Rotate the crown to change the mode to [TME].
3.
Pull the crown out to position
The second hand moves rapidly and returns to normal movement.
4.
Press and release the lower right button
button
.
B
The second hand points 0 second.
5.
Rotate the crown to adjust the time.
• When you rotate the crown quickly a few times, the hand will move
continuously. To stop the rapid movement, rotate the crown in either
direction.
• The hour, minute and 24-hour hands move synchronously.
• Check AM/PM referring to the 24-hour hand.
6.
Push the crown in to position
time source to finish the procedure.
Setting the calendar
1.
Pull the crown out to position
2.
Rotate the crown to change the mode to [CAL].
3.
Pull the crown out to position
The second hand indicates year and month currently set.
4.
Press and release the upper right button
change the indication to be corrected.
• Each time you press the button, the target changes as follows:
Year/month → date → day of week →(back to the top)
• The function hand moves back and forth fully around when the date
becomes adjustable.
• The function hand moves back and forth half around and points the day of
week when the day of week becomes adjustable.
5.
Rotate the crown to adjust indication.
• Year and month are indicated with the second hand.
"Month" corresponds to one of
the 12 zones shown in the figure
below.
Each number means month.
12
11
1
10
2
9
3
8
4
7
5
6
6.
Repeat steps 4 and 5.
7.
Push the crown in to position
.
1
.
2
or upper right
A
in accordance with a reliable
0
.
1
.
2
repeatedly to
B
"Year" corresponds to the years
since leap year and is indicated
with markers in the zone of each
month.
Years since leap year: 0 (Leap
year)
Years since leap year: 1
Years since leap year: 2
Years since leap year: 3
0
1
2
3
to finish the procedure.
0
Checking the reference position
1.
Pull the crown out to position
2.
Rotate the crown to change the mode to [u0t].
3.
Push the crown in to position
The hands and indication start to move to the current reference positions
stored in memory.
4.
Check the reference position.
Correct reference positions:
• Hour, minute and second hands: 0 hour 00 minute 0 second
• 24-hour hand: 24
• Function hand: MON
• Date indication: midway between "31" and "1"
When the current reference position is different from the correct one, adjust
the position following the steps of
5.
Pull the crown out to position
6.
Rotate the crown to change the mode to what you want.
7.
Push the crown in to position
Correcting the reference position
1.
Pull the crown out to position
2.
Rotate the crown to change the mode to [u0t].
The hands and indication start to move to the current reference positions
stored in memory.
3.
Pull the crown out to position
The second hand moves rapidly and stops to show the reference position
becomes become adjustable.
4.
Press and release the upper right button
change the hand/indication to be corrected.
• Each time you press the button, the target changes as follows:
Second hand → hour/minute/24-hour hand → function hand/date indication
→ (back to the top)
5.
Rotate the crown to adjust the hand/indication.
• When you rotate the crown quickly a few times, the hand/indication will
move continuously. To stop the rapid movement, rotate the crown in either
direction.
• Rotate the crown clockwise when adjusting the second hand. Rotating it
counterclockwise does not move the hand.
• Date indication changes to the next as the function hand rotates 5 times.
6.
Repeat steps 4 and 5.
7.
Push the crown in to position
After correcting the reference position
After correctiong the reference position, change the mode to [TME] and adjust
the time and calendar manually or by receiving time signals manually (on-demand
reception).
2/2
E61* Abbreviated instruction
.
1
.
0
Correcting the reference
position.
.
1
to finish the procedure.
0
.
1
.
2
repeatedly to
B
to finish the procedure.
0
Advertisement
