Download Print this page

Camec ELITE EM303 User Manual page 5

Caravan mover

Advertisement

Check that the caravan is disconnected from the battery supply and the mains electrical supply.
Only use adapters and accessories that are supplied or recommended by the manufacturer.
Check that the tyres are not worn and do have the same size and design (fitting to new or nearly new
tyres is the best option).
Make sure that the tyre-pressures are correct to the manufacturer's recommendation.
Make sure the chassis is in good condition without any damage and is free from rust, dirt etc.
Stop work immediately if you are in doubt about the assembly or any procedures and consult one of our
engineers (Please refer to contact information on the last page of this manual).
Locate the battery isolation switch to be accessible at all times when parking and moving the caravan.
Do not remove, change or alter any parts of the chassis, axle, suspension or brake mechanism. Any drilling of
holes in the chassis is not allowed.
Do not install the unit if you are under the influence of drugs, alcohol or medication that could impair your
ability to use the equipment safely.
INSTALLATION - MECHANICAL COMPONENTS
FOR PROFESSIONAL INSTALLATION ONLY. These instructions are for general guidance.
Installation procedures may vary depending on caravan type.
Working under a vehicle without appropriate support is extremely dangerous!
Please refer to Fig. 16 for an overview of the whole assembly fully fitted.
Place the caravan on a hard, level surface. The use of a lifting ramp or an assembly pit is ideal for access and
personal safety.
Unpack all the components and check for the presence of all parts (see package contents list). Write down, on
the product warranty registration card, the 10-digit serial number (this is located on an aluminium plate on the
side of one of the motor units).
Clean the area of your chassis where you need to mount all components to ensure a good fitting.
Make sure the caravan is prepared for installation. Check before installation that important areas, such as
drains/spare tyre etc. do not cause any obstruction to the function of the caravan manoeuvring system.
Ensure both rollers are in the DISENGAGED position (Fig. 12A), as the unit will not fit correctly otherwise (Note:
when fully disengaged, the pointer is positioned in the beginning of the yellow area).
Loosely assemble the left hand motor unit (1), right hand motor unit (2) and main cross bar (3) (Fig. 2). The
nuts (Fig. 2B), on the cross bar (3) to secure both motor units, must be no more than finger-tight at this stage.
Note: In principle, the unit should be fitted in front of the caravan road wheels, but if fitting in this position is
not possible because of obstacles or a too high hitch ball weight, it is permissible to fit it to the rear of the
wheels by rotating the whole assembly (Fig. 2) by 180° degrees.
Fit the Chassis Clamp Plates(36) to the chassis using bolts(37),nuts(38), washers(39) and spring washers(40), then
loosely fit the two aluminum clamp plates (7) to the plates (36) (Fig.
M10 and washers M10 (8,17,18) and put them in the diagonal positioned holes of the aluminium chassis clamp
plates. Nuts must be no more than finger-tight.
Assemble the pre-mounted manoeuvring system on the aluminium chassis clamp plates (7) by using the two
U-shaped brackets (9), bolts M10x50, nuts M10 and washers M10 (16,17,18). Nuts must be no more than
finger-tight.
Make sure that aluminium drive rollers of the motors are approximately on the same altitude as the centre
(axle) of the caravan wheel (± 20mm). To compensate a possible unevenness (and lower the motors), Camec
Elite
®
has a set of distance plates available. One set can compensate 15mm. In total three sets can be used so
that an altitude of 45mm can be compensated.
Adequate ground clearance: Please notice that the min. distance between the lowest line of
motors and ground is 110mm, no matter what kinds chassis or install situation.
CAMEC ELITE
"More information https://www.caravansplus.com.au"
8 & 16 ) and attach. Use the bolts M10x60, nuts
Ref: ELITE EM303-0814-Rev.A.
EM303
5

Advertisement

loading