Advertisement
14
Error messages via the remote control handset:
Error messages of the Camec Elite
control handset by the green LED (Fig. 5H), the error message LED's (Fig. 5I, 5J & 5K) and a buzzer
•
signal:
Green LED (Fig. 5H) off, no buzzer: remote control handset is turned off and also system is not activated
•
Green LED (Fig. 5H) continue on, no buzzer: remote control handset is turned on and system is activated
and ready to use.
Green LED (Fig. 5H) is blinking, no buzzer: no communication between handset and control unit. This could
•
be because of too much distance between remote control handset and control unit, or the battery isolation
switch for manoeuvring system is not turned on or that there is a distortion signal disturbing the
communication. As soon as connection is good again the green LED will be continue on and the system is
ready to use.
Blue battery voltage LED (Fig. 5K) is blinking in combination with buzzer (2 times blinking, break, 2 times
•
blinking, break etc.): Battery voltage too low (<10V). Battery needs to be recharged.
Blue battery voltage LED (Fig. 5K) is blinking in combination with buzzer (4 times blinking, break, 4 times
•
blinking, break etc.): Battery Voltage too high (over charged). Try to discharge the battery by turning on
an appliance (for example a lamp or water-pump).
Red overload LED (Fig. 5I) is blinking in combination with buzzer (6 times blinking, break, 6 times blinking,
•
break etc.): Amp overload protection is activated. Wait about 60 seconds and try again.
Blue 9V battery LED (Fig. 5J) is blinking, no buzzer: The internal 9V battery is near empty and needs to be
•
replaced.
Changing batteries in the remote control:
When the battery is empty (blue 9V battery LED (Fig. 5J) is blinking), it needs to be replaced.
Open the rear cover of the handset (Fig. 6A).
•
Take out the dead/old battery and dispose in the appropriate way.
•
•
Install a new replacement battery (Fig. 6.1). Make sure to use a leak proof PP3 (9Volt) battery (No claims
under guarantee can be considered for damage caused by leaking batteries).
•
Close the rear cover again.
Dead and used batteries may leak and damage the remote control handset! Remove the batteries if the
handset is not going to be used for an extended period.
OPERATION - ELECTRONIC CONTROL UNIT
The electronic control unit (32), which is mounted inside your caravan, is responsible for controlling the
manoeuvring system.
The control unit has three LED's, one pushbutton and one slide switch (Fig. 14):
Green LED (Fig. 14B): Power LED continuously illuminated when system is activated (by moving slide switch
to "On"-I). If the handset is far away from the control unit, beyond the connection distance, this LED will go
out.
Blue LED (Fig. 14C): Error message LED concerning caravan battery:
Blue LED is blinking (2 times blinking, break, 2 times blinking, break etc.): Battery voltage too low (<10V).
•
Battery needs to be recharged.
•
Blue LED is blinking (4 times blinking, break, 4 times blinking, break etc.): Battery Voltage too high (over
charged). Try to discharge the battery by turning on an appliance (for example a lamp or water-pump).
Red LED (Fig. 14D) is blinking (6 times blinking, break, 6 times blinking, break etc.): Amp overload protection
is activated. Wait about 60 seconds and try again.
In general all error messages will reset automatically after one minute. If this is not the case, reset the
electronics of the manoeuvring system by switching off the system via the isolation switch and the remote
control handset for at least 15 seconds and then turning it on again.
The Reset Button (Fig. 14A): The remote control handset and the control unit are synchronised with each
other in the factory. If the control unit or the remote control handset is replaced, they must be re-synchronised
as described below:
Check the installation in accordance with the installation instructions and ensure that the drive rollers are
•
not applied. Check that the battery is properly connected, check the condition of the battery and that a
voltage of 12 V is present at the control unit.
•
Please ensure that the battery isolation switch is on.
Activate the remote control handset by sliding the slide switch to "On"-I (Fig. 5A). The green LED on the
•
remote control handset (Fig. 5H) starts to flash slowly.
Press the reset button (Fig. 4A) on the control unit. All three LED's on the control unit (Fig. 14B, 14C & 14D)
•
will flash slowly.
•
Press both forwards (Fig. 5B) and reverse (Fig. 5C) button on the remote control handset for about 3
seconds. Then the handset buzzer will give a short beep to confirm that the synchronisation is complete.
After successful synchronisation, the green LED on the control unit (Fig. 14B) and on the remote control
•
handset (Fig. 5H) will illuminate continuously.
®
EM303 manoeuvring system will be communicated via the remote
CAMEC ELITE
"More information https://www.caravansplus.com.au"
Ref: ELITE EM303-0814-Rev.A.
EM303
Advertisement
