Related Manuals for Camec ELITE EM303
Summary of Contents for Camec ELITE EM303
- Page 1 ELITE Caravan Mover User Manual Model: ELITE EM303 Part No: 042373 For Professional Installation Only CAMEC ELITE EM303 Ref: ELITE EM303-0814-Rev.A. “More information https://www.caravansplus.com.au"...
- Page 2 Remote control handset wall holder Screw – M5x40 Chassis Clamp Plates (Pair) , nuts and washers with bolts M8 x70 Bolt - M8x70 Nylon nut M8 Washer 8mmØ Spring washer 8mmØ CAMEC ELITE Ref: ELITE EM303-0814-Rev.A. EM303 “More information https://www.caravansplus.com.au"...
- Page 3 Package Contents Fig.1 CAMEC ELITE Ref: ELITE EM303-0814-Rev.A. EM303 “More information https://www.caravansplus.com.au"...
- Page 4 INTRODUCTION Congratulations on choosing the Camec Elite ® EM303 caravan manoeuvring system. This has been produced according to very high standards and has undergone careful quality control procedures. By using the remote control handset you can move your caravan effortlessly into any position required within operating guidelines.
- Page 5 U-shaped brackets (9), bolts M10x50, nuts M10 and washers M10 (16,17,18). Nuts must be no more than finger-tight. Make sure that aluminium drive rollers of the motors are approximately on the same altitude as the centre (axle) of the caravan wheel (± 20mm). To compensate a possible unevenness (and lower the motors), Camec Elite ®...
- Page 6 Mark the motor cables (12 & 13) for both motor units using the cable markers (25). The cables for the left and the right motor should have the same length. Avoid any loops. CAMEC ELITE Ref: ELITE EM303-0814-Rev.A. EM303 “More information https://www.caravansplus.com.au"...
- Page 7 Finally find a suitable place for the remote control handset wall holder (34) and fix this by the supplied screws (out of reach of children or other unauthorised people). Installation of the caravan manoeuvring system is now complete. CAMEC ELITE EM303 Ref: ELITE EM303-0814-Rev.A. “More information https://www.caravansplus.com.au"...
- Page 8 Parts Identification & Fitting Diagrams Fig.2 Fig.3 Fig.5 Fig. 6 Fig. Fig. 6.1 Fig. 7 CAMEC ELITE Ref: ELITE EM303-0814-Rev.A. EM303 “More information https://www.caravansplus.com.au"...
- Page 9 Parts Identification & Fitting Diagrams Fig. 8.1 Fig. 8 Fig. 9 Fig.10 CAMEC ELITE EM303 Ref: ELITE EM303-0814-Rev.A. “More information https://www.caravansplus.com.au"...
- Page 10 Parts Identification & Fitting Diagrams Fig. 12 20mm Fig. 13 Fig. 14 10mm Fig. 15 Caravan Front CAMEC ELITE Ref: ELITE EM303-0814-Rev.A. EM303 “More information https://www.caravansplus.com.au"...
- Page 11 Parts Identification & Fitting Diagrams Fig.1 6 Fig.1 7 185mm (Min) 2.8mm to 3.5mm 30mm to 45mm 165mm (Min) 85mm (Min) 1800mm to 2500mm (Max) CAMEC ELITE Ref: ELITE EM303-0814-Rev.A. EM303 “More information https://www.caravansplus.com.au"...
- Page 12 This can be very dangerous! No warranty claim will be accepted and we cannot guarantee the function of the system if any modifications are made. We will not be liable for any damage whatsoever caused as a result of incorrect installation, operation or modification. CAMEC ELITE Ref: ELITE EM303-0814-Rev.A. EM303 “More information https://www.caravansplus.com.au"...
- Page 13 So always make sure the remote control handset is turned off by the slide switch. To reactivate the remote control, move slide switch to “Off” –O and then back to “On”-I after approximately 1 second. CAMEC ELITE Ref: ELITE EM303-0814-Rev.A. EM303 “More information https://www.caravansplus.com.au"...
- Page 14 Error messages via the remote control handset: Error messages of the Camec Elite ® EM303 manoeuvring system will be communicated via the remote control handset by the green LED (Fig. 5H), the error message LED’s (Fig. 5I, 5J & 5K) and a buzzer signal: •...
- Page 15 The single-twin axle function switch (Fig. 14S/T): The Camec Elite ® EM303 caravan manoeuvring system is suitable for both single axle and twin axle caravans. You just need to move the single-twin axle function switch (Fig 14S/T) on the control unit, so that the manoeuvring system can be used for a single-axle caravan or a twin-axle caravan (for 2 motor use but also for 4 motor use).
- Page 16 Once a year have your caravan manoeuvring system maintained and visually inspected. This inspection must include all the bolt/nut connections, the cables and electrical connections and lubrication of movable parts/joints. In case of any failure or problem, please contact your CAMEC ELITE ® supplier.
- Page 17 15 seconds and then turn them on again. Roller will not turn, spindle rotates freely: The motor or gear is broken, please contact your CAMEC ELITE ® supplier.
- Page 18 Contact Information New Zealand Australia Airport Business Centre 47-63 Remington Drive 44 Montgomerie Road, Mangere Dandenong South 3175 Phone: 0011 64 9 257 2419 Phone: 1300 4 CAMEC (22632) www.camec.com “More information https://www.caravansplus.com.au"...