Set-Up For Use - Philips SBCRU610/00U User Manual

Instructions for use

SET-UP FOR USE

A
D V I C E
Carefully read the complete procedure before starting!
Your equipment is a Philips brand:
1
Press the power key to test.
C
H E C K
Press a few keys to check correct response.
Your TV is of another brand, or your
equipment is a Philips brand, but not all keys
respond correctly:
1
Look up the brand name of the device you want to
operate in the code list (centre of this manual).
2
Make sure the device is switched on.
3
Press and hold keys 1 and 3 simultaneously - for about
1 3
three seconds- until the green LED lights up. (Release the
keys: the green LED should stay on)
-
9 4
1
Enter your 3-digit code using the number keys, within
30 seconds.
– The green LED flashes twice.
C
H E C K
That's it! Press a few keys to check correct response. If
response is not correct, repeat procedure beginning at step 1.
N
O T E
- If the LED displays one long flash, the code was not
recognised. Please go back to step 1 and repeat the
procedure, using the next 3-digit code in the list.
- If no key is pressed within 30 seconds, you have to start
again at step 1.
A
D V I C E
Carefully read the complete procedure before starting!
You do not know the brand of your TV/you can
not find the right code in the code list » auto
search:
1
Make sure the device is switched on.
2
1 3 Press and hold keys 1 and 3 simultaneously -for about
three seconds- until the green LED lights up.
(Release the keys: the green LED should stay on)
4
Instructions for use
3
Press the power key to start the search. Make sure that
you keep the remote control pointed at your equipment.
– Each time the green LED flashes, another code is sent.
When the right code is found, the equipment switches off.
Immediately press the power key to stop the search.
If the green LED flashed again after the equipment
switched off, this means you missed the correct code! If
you missed the code, follow the next proccedure, starting
at step 4. If the LED did not flash again after the
equipment switched off, go to step 6.
4
Switch the equipment manually back on.
5
Press 'PROG-' (down only!) repeatedly to send previous
PROG
codes until the equipment switches off again.
6
Press the power key to lock the correct code in the SBC
RU610's memory.
– The green LED flashes twice.
C
H E C K
Switch equipment on manually. Press a few keys to check correct
response. If response is not correct, repeat procedure beginning
at step 1.
N
O T E
- The search time averages about 90 seconds.
(Maximum search time is 5 minutes for TV).
- Autosearch stops automatically after all codes have been
tested.
MAKE A NOTE OF YOUR CODE!
A
D V I C E
Carefully read the complete procedure before starting!
Note the code inside the battery case and in the codelist in
the centre of this booklet. This may be useful if you ever need
to set up the SBC RU610 again. You used the auto search
procedure or you forgot to note the code after set up? No
problem! You can still 'read out' the code from the remote:
1
1
6 Press and release keys 1 and 6 simultaneously.
Important: after pressing the keys, you have to release them
immediately!
– The green LED lights up.
2
Press the two digits key.
– The green LED goes out.
3
1 Press key 1 and count the number of times the green LED
flashes. This is the first digit of the 3-digit code. (No
flashes means the digit is zero.)
2 4
Press key 2 and count the number of flashes for the second
digit.
5
3 Press key 3 and count the number of flashes for the third
digit.
6
Note the code.
5