Victor Pumps C Series Instruction And Maintenance Manual

Centrifugal pump

Advertisement

Quick Links

Instructions
Instruction and Maintenance
A. Declaration of Conformity
B. Introduction
C. Operation
D. Electric Motor
Pump No.
- Original -
Manual
Centrifugal Pumps
Type C
Index
www.victorpumps.com
16090170 / 09.09.2016 / 1 - 8
2
3
5
8

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Victor Pumps C Series

  • Page 1 Instructions 16090170 / 09.09.2016 / 1 - 8 - Original - Instruction and Maintenance Manual Centrifugal Pumps Type C Index A. Declaration of Conformity B. Introduction C. Operation D. Electric Motor Pump No. www.victorpumps.com...
  • Page 2: Declaration Of Conformity

    Instructions 16090170 / 09.09.2016 / 2 - 8 - Original - A. Declaration of Conformity We hereby declare that the self-priming centrifugal pumps type comply with the following relevant requirements: ⇒ EC Machinery Directive 2006/42/EC, Appendix II A. Pumps without a drive unit are intended to be connected to other machines. It is forbidden to start-up the machine in which the pump is installed if the machine has not been declared conform to the above named EC Directives.
  • Page 3: Shipment Inspection

    Instructions 16090170 / 09.09.2016 / 3 - 8 - Original - B. Introduction 1. Introduction The instruction manual contains important information on how to operate the pump safely, properly and most efficiently. Observing these instructions helps to avoid danger, to reduce repair costs, downtimes and to increase the reliability and life of pump.
  • Page 4 Instructions 16090170 / 09.09.2016 / 4 - 8 - Original - Shipment shortages, checked against the transport documents, should be reported to the carrier. Check the nameplate data against the shipping papers and against your purchase order to ensure that the proper pump is provided. 4.
  • Page 5: Operation

    Instructions 16090170 / 09.09.2016 / 5 - 8 - Original - C. Operation 1. Installation Set up the pump on a flat surface as near as possible to the liquid to be pumped. Make sure that the surrounding is adequately ventilated. Suction hose or pipe should be as short as possible and should have the same diameter as the pump port.
  • Page 6: Maintenance

    Instructions 16090170 / 09.09.2016 / 6 - 8 - Original - (c) Wrong direction of rotation or too low speed. (d) Overpressure in the delivery line. (e) Overheated liquid that vaporizes. This stops pumping. Wait until the liquid cools down or replace it with a cold liquid, then restart the pump.
  • Page 7: Warranty

    Instructions 16090170 / 09.09.2016 / 7 - 8 - Original - Each 6 months open the inspection cover or the casing and check inside. Remove possible foreign parts. Clean the pump and the motor. If necessary, check more frequently. Each 5-10 years make a general pump recondition. 6.
  • Page 8: Electric Motor

    Instructions 16090170 / 09.09.2016 / 8 - 8 - Original - D. Electric Motor 1. Introduction This section is valid only for close coupled pumps. For all other type of pumps, please see the separate motor instruction manual. The close coupled motor is equipped with stronger ball bearings and an extended shaft that is also the pump-shaft.
  • Page 9 Deutschland Italia Victor Pumpen GmbH Victor Pumps srl Dieselstr. 7 Viale Svezia 2 85551 Kirchheim bei München 35020 Ponte S. Nicolò (Padova) Tel. +49 (0)89 9048660 Tel. +39 0498961266 Fax +49 (0)89 9043447 Fax +39 0498961255...

Table of Contents