Special mode setting button AVR-S950H
b No. 1 - 4, 6 - 8 : While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power.
b No. 5, 9, 10 :
While the power is on, hold down buttons "A", "B", and "C" for at least 3 seconds .
No.
Mode
Version Display Mode
1
(u-COM / DSP Error Display)
PANEL / REMOTE LOCK Selection
2
Mode
3
Selecting the Mode for Service-related
3-1 Check the Video/Audio path Mode
3-2 Protection history display mode
232C Standby Clear Mode
3-3
(AVR-X2600H E3 Only)
3-4 Operation Info Mode
TUNER STEP Mode
3-5
(E3 and E2 model only)
3-6 Remote ID Setup Mode
4
Protection Pass Mode
5
Network Initialization Mode
6
User Initialization Mode
7
Factory Initialization Mode
8
Clearing the Operation Info
9
HDMI Diagnostics Mode
10 Log Capture feature
NOTE : When the volume indicator displays "
To release this special mode, press and hold the "ZONE2 SOURCE" and "TUNER PRESET CH +" buttons for 3 seconds or more while the power is ON. When the volume indicator returns to the normal
display, the RS-232C communication is available.
Button A Button B Button C
Displays the version of firmware such as the main firmware or DSP. Errors that have occurred are displayed.
DIMMER
STATUS
-
(See
1. Version Display
Start this unit in the PANEL/REMOTE LOCK selection mode so that PANEL LOCK and Remote Lock can be switched between On and
ZONE2
TUNER
-
SOURCE
PRESET CH +
Off. (See
2. PANEL / REMOTE LOCK Selection
This is a display for turning on each service-related mode.
TUNER
TUNE -
TUNE +
PRESET CH +
Service-related modes : No. 3-1 - No. 3-6 (See
This is a special mode for service confirmation used during repair work to simplify the confirmation work for the Audio channel /
↑
↑
↑
video channel. (See
Displays the protection occurrence history. (See
↑
↑
↑
Switches from 232C standby mode to normal standby mode.
↑
↑
↑
(See
3-3. 232C Standby Clear Mode (AVR-X2600H E3
Displays the accumulated operating time of the unit, the number of times the power was switched on, and the number of occur-
↑
↑
↑
rences of each protection. (See
Enables reception STEP of the ANALOG TUNER to be changed.
↑
↑
↑
(See
3-5. TUNER STEP mode (E3 / E2 only, Except
If there are multiple DENON AV receivers in the same area, this mode prevents other AV receivers from being operated concurrently
↑
↑
↑
with this device. (See
Enables the power to be turned on when protection detection is disabled.
ZONE2
TUNER
TUNE +
SOURCE
PRESET CH +
(See
4. Protection Pass
Network module backup data is initialized.
ZONE2
ZONE2
-
ON/OFF
SOURCE
(See
5. Network Initialization
TUNER
TUNER
Initialize the backup data for the MCU and network module. (Settings for the Installer Setup are not initialized.)
-
PRESET CH -
PRESET CH +
Initialize the backup data only for MCU.
TUNER
TUNE -
-
(Settings for the Installer Setup are initialized) (Network function settings are not initialized.) (See
PRESET CH +
Clear the accumulated operating time of the unit, the number of times the power was switched on, and the number of occurrences
TUNER
TUNE +
-
PRESET CH +
of each protection. (See
This mode is used to identify and solve the cause when there is a connectivity issue with this unit and an HDMI device.
ZONE2
TUNER
-
For details on the operating methods and diagnosis procedures, see the HDMI Diagnostics and Troubleshooting guide issued on SDI.
SOURCE
PRESET CH -
Acquires the Network Module log. The log is deleted when the Network Module is deleted.
MOVIE
MUSIC
(See
7. Log Capture
", the unit has entered a special mode for developers. In this case, the RS-232C communication is not available.
All the indicator Lights
ZONE2
X
ON/OFF
Mode)
Mode)
3-1. Selecting the Mode for
Service Path Check
Mode)
3-2. Protection History Display
Only))
3-4. Operation Info
Mode)
DABE2))
3-6. Remote ID Setup
Mode)
Mode)
Mode)
6. Clearing the Operation
Info)
feature)
ZONE2
TUNER
TUNE +
MUSIC
STATUS
SOURCE
PRESET CH +
TUNER
TUNE -
MOVIE
DIMMER
PRESET CH -
127
Descriptions
Service-related)
Mode)
POST-SERVICE
PRECAUTIONS)