Special Mode Setting Button - Denon AVR-X6300H Service Manual

SPECIAL MODE

Special mode setting button

b No. 1 - 4, 6 - 8 : While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power.
b No. 5 : While the power is on, hold down buttons "A" and "B" for at least 3 seconds .
No. Mode
Version Display
1
(u-COM / DSP Error Display)
PANEL / REMOTE LOCK Selection
2
Mode
PANEL LOCK Mode
2-1
(with Volume)
PANEL LOCK Mode
2-2
(without Volume)
2-3 PANEL LOCK mode is turned off
3 Selecting the Mode for Service-related
3-1 Check the Video/Audio path Mode
3-2 Protection history display mode
3-3 232C Standby Clear Mode
3-4 Operation Info Mode
TUNER STEP Mode
3-5
(E2 model only)
3-6 Remote ID Setup Mode
4 Protection Pass Mode
5 Network Initialization Mode
6 User Initialization Mode
7 Factory Initialization Mode
8 Clearing the Operation Info
h NOTE : When the volume indicator displays "
To release this special mode, press and hold the "STATUS" and "CURSOR f " buttons for 3 seconds or more while the power is ON. When the volume indicator returns to the normal display, the RS-232C
communication is available.
Button A Button B Button C
Displays the version of firmware such as the main firmware or DSP. Errors that have occurred are displayed.
SETUP OPTION -
(See 1. Version Display
Start this unit in the PANEL/REMOTE LOCK selection mode so that PANEL LOCK and Remote Lock can be switched between On
and Off. (See
STATUS INFO -
PANEL LOCK MODE : No. 2 - 1 - No. 2 - 3
Disables reception from all keys and encoders on the front panel except the power button (including the volume).
↑ ↑ -
Disables reception from all keys and encoders on the front panel except the power button and volume encoder.
↑ ↑ -
Releases the PANEL LOCK.
↑ ↑ -
This is a display for turning on each service-related mode.
ZONE3
STATUS -
SOURCE Service-related modes: No. 3-1 - No. 3-4 (See
This is a special mode for service confirmation used during repair work to simplify the confirmation work for the Audio channel /
↑ ↑ -
video channel. (See
Displays the protection occurrence history.
↑ ↑ -
(See 3-2. Protection History Display
Switches from 232C standby mode to normal standby mode.
↑ ↑ -
(See 3-3. 232C Standby Clear
Displays the accumulated operating time of the unit, the number of times the power was switched on, and the number of occur-
↑ ↑ -
rences of each protection. (See
Enables reception STEP of the ANALOG TUNER to be changed.
↑ ↑ -
(See 3-5. TUNER STEP mode (E2
If there are multiple DENON AV receivers in the same area, this mode prevents other AV receivers from being operated concur-
↑ ↑ -
rently with this device. (See
Enables the power to be turned on when protection detection is disabled.
ZONE3
STATUS CURSOR 0
SOURCE (See 4. Protection Pass
Network module backup data is initialized.
CURSOR 1 DIMMER -
(See 5. Network Initialization
Initialize the backup data for the MCU and network module. (Settings for the Installer Setup are not initialized.)
BACK INFO -
Initialize the backup data only for MCU.
(Settings for the Installer Setup are initialized) (Network function settings are not initialized.)
CURSOR d CURSOR f -
(See Initializing This
Clear the accumulated operating time of the unit, the number of times the power was switched on, and the number of occur-
OPTION DIMMER -
rences of each protection. (See
", the unit has entered a special mode for developers. In this case, the RS-232C communication is not available.
Mode)
2. PANEL / REMOTE LOCK Selection Mode)
3-1. Selecting the Mode for
Service Path Check Mode)
Mode)
Mode)
3-4. Operation Info Mode)
only))
3-6. Remote ID Setup Mode)
Mode)
Mode)
Unit)
6. Clearing the Operation Info)
Go to next page.
126
Descriptions
Service-related)